分偏移距动校正方法的改进

在地震资料处理中，速度分析和动校正对资料品质的影响很大。由于动校正速度是随偏移距变化而变化的，而常规速度分析并没有考虑这一因素，动校正效果往往不是很理想，从而影响资料的叠加和成像效果。分偏移距动校方法是在不同偏移距上采用不同的速度进行动校正。但由于是在不同偏移距组上分别独立进行速度分析和动校正，因此不能将不同偏移距组的同一反射同相轴校正到同一to层位上。这样就需要进行繁琐的后续处理，而且还会降低同相轴的连续性和平滑性。为此，对该方法进行了一些改进，即固定to在不同的分偏移距段进行速度扫描，段与段之间的衔接问题采用平滑处理解决。理论模型分析表明，采取上述改进措施后，动校正效果得到了一定提高，改善了同相轴的连续性和平滑性。     

Optimal control of nonlinear systems to given orbits

Using optimal control techniques we derive and demonstrate the use of an explicit single-step control method for directing a nonlinear system to a target orbit and keeping it there. We require that control values remain near the uncontrolled settings. The full nonlinearity of the problem in state space variables is retained. The “one-step” of the control is typically a composition of known or learned maps over (a) the time required to learn the state, (b) the time to compute the control and (c) the time to apply the control. No special targeting is required, yet the time to control is quite rapid. Working with the dynamics of a well-studied nonlinear electrical circuit, we show how this method works efficiently and accurately in two situations: when the known circuit equations are used, and when control is performed only on a Poincaré section of the reconstructed phase space. In each case, because the control rule is known analytically, the control strategy is computationally efficient while retaining high accuracy. The target locations on the selected target trajectory at each control stage are determined dynamically by the initial conditions and the system dynamics, and the target trajectory is an approximation to an unstable periodic orbit of the uncontrolled system. A linear stability analysis shows that dissipation in the dynamical system is essential for reaching a controllable state.     

提高海水温度对锌合金和铝合金牺牲阳极电化学性能的影响

研究了提高海水温度对锌合金和铝合金牺牲阳极电化学性能的影响。结果表明，锌合金和铝合金牺牲阳级的电化学性能都随着海水温度的提高而变劣；凡是发生晶间腐蚀的合金，其晶间腐蚀程度都随着海水温度的提高而加剧。低含铝量的锌－铝－镉合金阳极在７０℃海水介质中，工作电位仍负于－１．０１０Ｖ，电流效率＞８０％，阳极工作表面溶解均匀，且不产生晶间腐蚀。     

用载文南定理计算感应电机和变压器的特性曲线

感应电机和变压器激磁电路的参数是非线性的.为准确求取它们的特性曲线,需要的计算量很大.应用本文引入的方法可以避免大的计算量又可得到准确的特性曲线.     

粘合剂流变特性的研究(待续)

本文从流变学的观点出发,分析粘合剂在配制及粘结过程中,反映出不同的流变特性,而粘合剂本身的流动、粘度、触变性与涂胶及其粘合的质量关系重大。     

固定床吸附器透过曲线参数优化方法

开发了一种固定床吸附器透过曲线参数估值的优化方法，用Ｂａｓｉｃ语言编制了运算程序，并在普及型２８６微机上考核了该法的可靠性，相对误差在１％以下，运算机时７．５ｍｉｎ。     

衰减曲线分析的诺模图

基于Arps递减方程,建立了衰减曲线分析的诺模图。应用该诺模图,可以方便地确定油气田的可采储量。     

虚拟肝脏的规则和非规则手术切除技术

为了提高肝癌手术治疗计划的可靠性,在利用腹部CT图像数据进行肝脏三维重建的基础上,实现了任意角度对虚拟肝脏进行平面切割和切割面结构的显示;通过构造可以调节大小、位置的球体模型,实现了球体切除;通过在肝脏三维模型表面上勾画不规则封闭区域,实现了任意曲面肝脏切除;并依据肝内血管结构进行肝段划分,实现了解剖性肝段切除.临床实验结果表明,文中所述的技术能够满足虚拟手术的需求,有利于医生制定安全可靠的术前计划,提高手术成功率.     

阿姆河流域耕地变化及水土匹配特征分析

基于中亚阿姆河流域4个分区1990—2015年间土地利用变化和水资源等数据,运用耕地变化速率、洛伦兹曲线和基尼系数法以及水土资源匹配系数对阿姆河流域耕地变化和水土匹配状况进行了综合分析。结果表明:1990—2015年阿姆河流域耕地以146.74 km²/a的速度在扩张,且各时期、各分区扩张的速度不同;在不考虑咸海来水不断减少、生态持续恶化的前提下,绿洲区匹配状况属比较公平和相对合理状况;阿姆河流域水土资源空间分布存在明显的错位现象;全流域生态用水被农业用水严重挤占,阿姆河流域灌溉面积、灌溉用水量成为影响咸海水量及面积变化的重要因素,是一种不可持续的用水方式。     

A relation between interfacial and bulk properties along the saturation curve

A liquid-vapor interface in thermal equilibrium was considered, where the pressure tensor depends upon the density (z) and the position z. The surface tension coefficient results are parametrized with the bulk compressibility, liquid-vapor density difference, and interfacial width along the saturation curve. Previous results at the triple and critical points reported by other investigators are verified. Also included is a plot of the computed results using the parametric equation and experimental data for different substances.