Flame spread over thin fuels in actual and simulated microgravity conditions

Most previous research on flame spread over solid surfaces has involved flames in open areas. In this study, the flame spreads in a narrow gap, as occurs in fires behind walls or inside electronic equipment. This geometry leads to interesting flame behaviors not typically seen in open flame spread, and also reproduces some of the conditions experienced by microgravity flames.Two sets of experiments are described, one involving flame spread in a Narrow Channel Apparatus (NCA) in normal gravity, and the others taking place in actual microgravity. Three primary variables are considered: flow velocity, oxygen concentration, and gap size (or effect of heat loss). When the oxidizer flow is reduced at either gravity level, the initially uniform flame front becomes corrugated and breaks into separate flamelets. This breakup behavior allows the flame to keep propagating below standard extinction limits by increasing the oxidizer transport to the flame, but has not been observed in other microgravity experiments due to the narrow samples employed. Breakup cannot be studied in typical (i.e., “open”) normal gravity test facilities due to buoyancy-induced opposed flow velocities that are larger than the forced velocities in the flamelet regime.Flammability maps are constructed that delineate the uniform regime, the flamelet regime, and extinction limits for thin cellulose samples. Good agreement is found between flame and flamelet spread rate and flamelet size between the two facilities. Supporting calculations using FLUENT suggest that for small gaps buoyancy is suppressed and exerts a negligible influence on the flow pattern for inlet velocities ?5 cm/s. The experiments show that in normal gravity the flamelets are a fire hazard since they can persist in small gaps where they are hard to detect. The results also indicate that the NCA quantitatively captures the essential features of the microgravity tests for thin fuels in opposed flow.     

Flow and heat transfer of couple stress fluid in a porous channel with expanding and contracting walls

In this paper, an incompressible laminar flow of a couple stress fluid in a porous channel with expanding or contracting walls is considered. Assuming symmetric injection or suction along the uniformly expanding porous walls and using similarity transformations, the governing equations are reduced to nonlinear ordinary differential equations. The resulting equations are then solved numerically using quasilinearization technique. The graphs for velocity components and temperature distribution are presented for different values of the fluid and geometric parameters.     

Improved Side‐Channel Attack on DES with the First Four Rounds Masked

This letter describes an improved side‐channel attack on DES with the first four rounds masked. Our improvement is based on truncated differentials and power traces which provide knowledge of Hamming weights for the intermediate data computed during the enciphering of plaintexts. Our results support the claim that masking several outer rounds rather than all rounds is not sufficient for the ciphers to be resistant to side‐channel attacks.     

楔形头部试样的ECAP变形行为有限元模拟

应用三维有限元方法对楔形头部试样在等径弯曲通道挤压(ECAP)中的变形行为进行了模拟分析,以比较不同楔形方案(前楔形、后楔形以及楔形头部大小)对金属ECAP变形的影响.结果表明:试样头部为后楔形可以有效的降低加工载荷,显著改善应力/应变分布的均匀性,消除应变集中,避免折叠缺陷,从而获得组织性能较为均匀的试样.     

Asymptotic throughput analysis of multicast transmission schemes

This paper demonstrates the use of extreme value theory in the asymptotic throughput analysis of wireless multicast and unicast for large number of users. Exact analysis of these schemes involves finding the probability distributions of maxima or minima of signal to noise ratios (SNRs). Jointly considering random user distribution and Rayleigh fading, exact distributions of these extreme values become complex and lack insights. On the other hand, asymptotic expressions obtained by using extreme value theory are quite accurate even for moderate number of users and they give insights about the performances without using simulations. The results of this analysis can be used in designing cellular unicast and multicast systems.     

Thermal behavior in a 180-deg turned channel with the perforation divider under rotational condition

This study provided a new configuration of the 180-deg turned channel with a perforation divider. The perforations cross the divider let the coolant at the first duct to bypass into the second duct early, preventing from the local high temperature at the downstream zone. Additionally, the perforation-induced disturbing flow should enhance the total heat transfer. This work experimentally investigated the heat transfer behaviors of such system under the rotational condition. The results indicated that the perforation would reduce the raise of the local heat transfer at the turned region. Besides, the rotation would obviously influence the local heat transfer on the leading and trailing surfaces. Furthermore, the effect of rotation on the total heat transfer was insignificant. Finally, the perforation system with the relative perforation diameter d/D_h = 2/4 had the similar total heat-transfer capacity with that without perforation; the total heat-transfer capacity of the perforation system with d/D_h = 1/4 was around 20% higher than the non-perforation one.     

A modification on ECAP process by incorporating torsional deformation

In the present study, integration of equal channel angular pressing (ECAP), as a well known severe plastic deformation (SPD) technique, and torsion deformation, is studied by using three dimensional finite element analysis. This process is to be named as torsional-equal channel angular pressing (T-ECAP). In this modification a part of the exit channel in the ECAP die is rotating around its axis, to impose extra shear strains to the samples. To study deformation behavior in the T-ECAP process, three-dimensional finite element analysis (FEA) was carried out by using the elasto-plastic finite element analysis ABAQUS/Explicit Simulation. To investigate the validity of the simulation results, experimental studies were furthermore performed on commercially pure aluminum (AA 1050). Vickers hardness test was used to determine the distribution of hardness on both normal and longitudinal sections of the deformed samples with respect to the exit channel of the die. The hardness test results showed more uniform distribution of hardness in both sections of the T-ECAP processed samples regarding the ones produced by ECAP process. The load requirement comparison for performing both processes showed lower value for the T-ECAP with respect to the ECAP process. The simulation results for the strain values showed higher magnitude and more uniform distribution for the T-ECAP with respect to the ECAP process.     

Quantitative measurement of cementite dissociation in drawn pearlitic steel

Fractional dissociation of cementite was quantified as a function of strain by measuring the volume change of cementite in the pearlitic steel. The amount of carbon dissolved into the ferrite was estimated from the decrease of cementite volume, to correlate with the hardness in different strain level. The hardness showed linear relationship with the carbon dissolved into the ferrite matrix, which is believed to contribute in strengthening the drawn wire. Defects introduced from the deformation were believed to lower the energy barrier of cementite break-ups and to enhance the dissolution of carbon into ferrite.     

Microstructure control during severe plastic deformation of Al-Cu-Li and the influence on strength and ductility

The microstructure and mechanical behaviour of an Al-Cu-Li alloy has been examined after processing over a wide range of conditions involving severe deformation at elevated temperatures with prior or subsequent heat treatments. Dislocation cellular or subgrain structures are obtained, with varying degrees of precipitation. High strength, as well as poor ductility, can be correlated with the presence of a high density of fine T₁ phase precipitates, with the dislocation substructure playing a smaller role. Careful control of processing conditions allows a suitable combination of good strength with ductility to be obtained.