Global optimization for power dispatch problems based on theory of moments

Non-convex of an optimal power dispatch problem makes it difficult to guarantee the global optimum. This paper presents a convex relaxation approach, called the Moment Semidefinite Programming (MSDP) method, to facilitate the search for deterministic global optimal solutions. The method employs a sequence of moments, which can linearize polynomial functions and construct positive semidefinite moment matrices, to form an SDP convex relaxation for power dispatch problems. In particular, the rank of the moment matrix is used as a sufficient condition to ensure the global optimality. The same condition can also be leveraged to estimate the number of global optimal solution(s). This method is effectively applied to {0,1}-economic dispatch (ED) problems and optimal power flow (OPF) problems. Simulation results showed that the MSDP method is capable of solving {0,1}-ED problems with integer values directly, and is able to identify if more than one global optimal solutions exist. In additional, the method can obtain rank-1 moment matrices for OPF’s counterexamples of existing SDP method, this ensures the global solution and overcomes the problem that existing SDP method cannot meet the rank-1 condition sometimes.     

Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

Entry into force of the UN Watercourses Convention: why should it matter?

The United Nations Watercourses Convention entered into force on 17 August 2014, following a long and complex journey that dates back to 1970 when the UN referred the matter to its legal arm, the International Law Commission. This article follows the Convention through that long and turbulent road, examines its main provisions and analyses the reasons for the delay of its entry into force. It concludes by answering the question of why entry into force of the Convention should indeed matter.     

A conceptualization of intended learning outcomes supporting self‐regulated learners in indicating learning paths

Intended learning outcomes (ILOs) indicate what learners will be able to achieve after they are taught. Traditionally, ILOs are expressed as plain text or unstructured documents. What if all ILOs of a specific course of study can be conceptualized through a structured diagrammatic technique? It was hypothesized that learners can benefit from this conceptualization in learning, especially in self‐regulated learning. The aim of this study was to investigate whether the ILOs represented in unstructured or structured formats can facilitate learners to identify learning paths. The results revealed that the mean ratings of all learning paths were statistically significantly higher with structured ILOs.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

无失效数据机载多余度EWIS可靠性研究

针对高可靠度机载多余度EWIS各组成部分寿命服从指数分布但参数未知的情况，提出采用无失效数据可靠度分析方法评估EWIS的可靠度水平。通过Monte-Carlo仿真方法对连接形式为“先并联、后串联”EWIS各组成部分寿命进行抽样，利用“最小最大值”方法获得系统寿命的抽样值，用概率纸检验法初步判断EWIS寿命是否服从威布尔分布，再用Pearson拟合优度检验法判断EWIS寿命是否服从威布尔分布。结合无故障飞行时间的样本值与EWIS寿命服从威布尔分布的假设，采用无失效数据分析方法评估EWIS的可靠度水平。研究方法对机载多余度EWIS无失效数据可靠度分析有一定的贡献。     

苯乳酸抑制链格孢霉作用靶位的分析

以从自然腐败的樱桃上分离的链格孢霉（Alternaria sp.）LD3.0086为指示菌，研究苯乳酸对链格孢霉的主要抑制作用靶位。应用分光光度法测定苯乳酸对链格孢霉的最小抑菌浓度，通过卡尔科弗卢尔荧光增白剂染液（calcofluor white，CFW）染色观察苯乳酸对菌丝顶端生长的破坏作用，利用扫描电子显微镜和透射电子显微镜观察链格孢霉的超微结构变化，通过测定苯乳酸作用前后链格孢霉上清液中N-乙酰葡萄糖胺质量浓度变化研究苯乳酸对菌丝细胞壁的破坏作用，应用荧光双染色法观察苯乳酸对链格孢霉菌丝细胞膜的损伤作用。结果表明，12.5 mmol/L的苯乳酸能有效抑制链格孢霉的生长；与对照组（无菌水处理）相比，苯乳酸处理后链格孢霉顶端生长细胞无明显形变，经12.5 mmol/L苯乳酸处理的链格孢霉上清液中N-乙酰葡萄糖胺质量浓度基本不变；苯乳酸处理24 h，链格孢霉菌丝细胞壁表面无明显损伤，细胞内结构发生明显变化；苯乳酸短时间（4 h）处理链格孢霉，菌丝细胞膜仍较为完整，加入苯乳酸较长时间（8 h）后细胞膜发生破裂。综合分析可知，苯乳酸对链格孢霉的主要作用靶位应不是菌丝体的细胞壁和细胞膜，而是在菌丝体内部，通过破坏菌丝内部细胞器结构或引起细胞内的生化反应，从而抑制链格孢霉的生长和繁殖，发挥抑菌活性。     

Systematic optimization of corrosion,bioactivity, and biocompatibility behaviors of calcium-phosphate plasma electrolytic oxidation (PEO) coatings on titanium substrates

To optimize the corrosion, bioactivity, and biocompatibility behaviors of plasma electrolytic oxidation (PEO) coatings on titanium substrates, the effects of five process variables including frequency, current density, duty cycle, treatment time, and electrolyte Ca/P ratio were evaluated. In our systematic study, a Taguchi design of experimental based on an L16 orthogonal array was used. For this, the coatings characteristics such as the surface roughness, wettability, rutile to anatase and Ca/P ratios, and corrosion polarization resistance were investigated. After determining the optimum process variables for each response, the apatite forming ability in SBF (bioactivity behavior) and MG63 cell attachment and flattening (biocompatibility behavior) for two groups of coatings were examined. The first group was optimized based on the maximum corrosion polarization resistance and the variables were set as the frequency of 2000 Hz, the current density of 5 A/dm², the duty cycle of 30%, the treatment time of 5 min, and the Ca/P ratio of 0.65 at. % in the electrolyte. For the second group, the maximum surface roughness, greatest Ca/P ratio, and highest wettability as well as the minimum rutile to anatase ratio in coatings, could be obtained when the variables were set as the frequency of 10 Hz, the current density of 12.5 A/dm², the duty cycle of 50%, the treatment time of 12.5 min, and the Ca/P ratio of 1.70 at. % in the electrolyte. The results showed that while both groups of coatings indicated a significant apatite forming ability and can serve as bioactive coatings, a proper attachment and flattening of cells and consequently, the favorable biocompatibility properties were seen only in the first group.     

Recent activities in the field of Nuclear Operational Management and Nuclear Safety Engineering

Recent activities in the field of Nuclear Operational Management and Nuclear Safety Engineering, the studies related to risk analysis methodology, design, and operational management, physical phenomena, and emergency preparedness and nuclear security, have been progressed. Especially, ‘risk analysis methodology’ and ‘design and operational management’ are the main categories of the field, in which more than half of published articles on Journal of Nuclear Science and Technology are related to these categories.