Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

Design for a high power-density Astron reactor

A liquid lithium blanket surrounding the plasma volume is described. The liquid lithium flows along magnetic flux tubes at a high speed. There is no vacuum wall between the blanket and the plasma. The E-layer of relativistic particles within which the plasma is confined serves as a vacuum wall protecting the plasma from the lithium vapor, which is continuously produced at the surface of the blanket, by ionizing the lithium atoms and ejecting the same along open magnetic lines. The heat load at the surface of the blanket generated by 14 MeV neutrons can be several hundred MW per square meter.Work performed under the auspices of the U.S. Atomic Energy Commission.Deceased September 24, 1972.     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

N.m.r. study of the ferroelectric phase transition in a 7030mol% copolymer of vinylidene fluoride (VF2) and trifluoroethylene (TrFE)

Nuclear magnetic resonance (n.m.r.) studies of ¹⁹F nuclei in a $\text{70}\text{30}\text{mol}\text{\%}$ random copolymer of vinylidene fluoride and trifluoroethylene were performed at 9.14 MHz and 20.0 MHz. The free induction decays (FIDs) were analysed in terms of two T₂ components attributed to the amorphous and crystalline portions of the polymer. The changes in crystallinity as well as the effects of the ferroelectric transition were observed during cycles of heating and cooling between 20°C and 140°C. The crystalline component of the FID lengthens by a factor of 2 at 100°C on heating and decreases by this factor at 60°C on cooling, thus exhibiting the thermal hysteresis of this ferroelectric transition. The spin-lattice relaxation was also investigated. From measurements at 9.14 MHz the observed longitudinal relaxation time T₁ appears to be dominated by the dynamics of the amorphous phase and exhibits no anomaly through the phase transition. However, from measurements at 20 MHz, well defined minima of T₁ were observed, which are associated with the ferroelectric transition (especially after repeated annealing of the samples). Results are discussed in terms of the crystalline phase structure, which appears dynamically disordered above the ferroelectric phase transition. An analogy is considered with the plastic phase transitions encountered in molecular crystals.     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.     

Treatment of Humic Waters By Ozone

Two different generators for ozone were tested, a traditional electrical discharge generator and a generator based upon UV–irradiation of air at 150–180 nm. It was demonstrated that the traditional generator gave slightly higher reductions in levels of color for equivalent ozone dosages. Both gases affected the molecular weight distribution in the way that the bigger molecules were broken down to smaller ones. No significant difference between the molecular weight reduction efficiency of the gases was found.     

HHD型核子秤电离室物理性能检测

HHD型核子秤电离室已成功地使用于HCS型核子秤.对它的各种物理性能指标进行了检测,各项性能指标都达到了设计要求。     

Combined shape and sizing optimization of truss structures

 In this paper, an evolutionary optimization method is presented for weight minimum problem of a 3-dimensional truss structure in terms of nodal coordinates and element cross-sectional areas. The structure is subject to stress, local buckling and displacement constraints. Two types of design variables with different natures are optimized separately: (1) a fully stressed design (FSD) and scaling techniques are applied to sizing variables and (2) the evolutionary node shift method is applied to shape variables. Alternating procedure is utilized to couple the two types of variables and to combine the results. The optimum solution is achieved gradually from the initial configuration design. Two typical truss structures are examined to illustrate the validity of the method. Received: 22 October 2001 / Accepted: 04 June 2002 This research work is supported by the National Natural Science Foundation of China under the guarantees no. 10072050 and 10172072, respectively.