基于有限体积法的G4-73型离心风机三维流场数值模拟

基于有限体积法,利用Fluent软件对G4-73型离心风机内部流场进行了全三维数值模拟。结果表明:蜗壳内的低能流体区沿轴向朝流动方向推进;叶轮内的静压和动压在叶片吸力面靠近叶轮进口处最低,叶轮流道中动压等值线呈"凸"型分布,在叶片压力面靠近叶轮出口处静压和动压达到最大值,且叶轮出口相对总压损失集中在吸力面和前盘侧。     

促进发电节能的可中断负荷电价优化设计模型

如果电力系统的备用容量完全有发电机组来承担,可能会产生长期"备而不用"的问题.这不仅会造成资源的浪费,也会导致用户购电成本的增加.通过供电公司与用户之间签订的合同,把用户的可中断负荷作为发电的一种备用,如果系统供给能量,则用户需要向供电公司支付电能价格;如果备用容量不足,系统中断时该用户的电力供给,但供电公司向用户进行其低谷用电的电价赔偿.可中断负荷电价的确定既要有利于发电成本的下降,又要有利于保护供电企业的利益,还要有利于激励用户减少高峰负荷用电的积极性.正是基于这样的目的而讨论可中断电价的优化设计模型.     

延长生焦时间对延迟焦化装置的影响

国内焦化装置的生焦时间几乎都采用24小时，设计的焦炭塔空高较大，在装置低负荷生产时，适当延长生焦时间，不仅可降低装置的运营成本、提高焦炭质量、降低劳动强度，而且还可降低维修费用。安庆焦化成功地在一套装置上实现了48小时生焦操作，年运行200天，增效约100万元。     

On the oxidation kinetics and mechanisms of various SiC-coated carbon-carbon composites

SiC coatings on the surface of C-C were produced by either silicone resin impregnation/ pyrolysis or reaction sintering. Cycles of resin impregnation/pyrolysis produced an SiC coating, on the walls of fine open pores, which was effective in reducing the oxidation rate of C-C and in shifting the transition temperature to a higher value. Unless it is pre-coated with a pyrocarbon layer before sintering, plain reaction sintered SiC has oxidation behaviors similar to those of the above-mentioned SiC. The dense pyrocarbon film deposition on the surface of C-C could form a better SiC film than others. The carbon film homogenized the surface of C-C and a dense SiC film was established. The oxidation of the coated C-C can be modelled by a set of “oxidation resistors” in series and/or in parallel, with each resistor corresponding to an oxidation element. The controlling mechanism can be resolved from the activation energy. A combined resistant layer, consisting of resin impregnation, pyrocarbon film and reaction sintering SiC, showed the best oxidation resistance of any single-layer coated C-C composite.     

Periplaneta americana perception of phytochemical naphthoquinones as allelochemicals

Electrochemistry of malePeriplaneta americana perception of naphthoquinones as allelochemicals is presented. Importance of the oxidation-reduction potential and hydrogen-bonding capabilities of the naphtho-quinone messenger to its exchange of energy with the information-encoding, redox protein of the chemosensory neuron is considered. Evidence that the required information is initially encoded by an electroreactive protein in dendritic membrane is analyzed. A sulfhydryl-disulfide protein-based electrochemical mechanism for the demonstrated linear conversion of a molecular messenger energy state into whole insect behavior (avoidance or feeding inhibition) is elucidated. Even though the information-encoding mechanism is genetically conserved (kept electrochemically similar) within the species, behavioral biotypical differences regarding sensitivity to naphthoquinones are allowed through a group of proteins in the outer aqueous medium in the chemosensory sensillum. Such proteins electrochemically interface the dendritic membrane of the chemosensory neuron in the sensillum with the environment external to the sensillum. These interfacing proteins bind (complex) with chemical messengers (e.g., naphthoquinones) and/or variously degrade them, and thus determine the amount (moles) that is required in the environment to result in stimulation of the underlying sensory neurons and in a changed behavior.     

ZrO2对CaO-SiO2系玻璃析晶的影响

通过DSC曲线研究了不同含量的ZrO2对CaO-SiO2系玻璃析晶的影响,根据JMA方程计算动力学参数(如析晶活化能E、频率因子ν、晶化指数n)。从计算结果可以看出,随着ZrO2含量的增加,析晶活化能E减少,而频率因子ν和晶化指数n增加。当ZrO2含量为7%时,E值最小:235.58kJ/mol;n值最大:4.70。说明ZrO2在CaO-SiO2玻璃体系是有效的晶核剂。     

Design of the low power wake-up receiver for internet of things communication

A wake-up receiver with high energy efficiency and low power consumption is proposed for solving the power consuming problems of wireless nodes communication in the Internet of Things. The proposed wake-up receiver based on the wake-up mechanism can effectively schedule the network nodes communication, and use the simple envelope detection structure to achieve frequency down-conversion, which can flexibly manage energy and reduce power consumption. Based on UMC 65nm CMOS process technology, the wake-up receiver is designed and simulated. The results show that it can achieve S₁₁ of -21dBm and a sensitivity of -75dBm at a data rate of 1Mb/s, when operating at the central frequency of 780MHz and input signal adopting an on-off keying (OOK) modulation, and the power consumption is 82μW at 1.2V voltage supply.     

酒店暖通设计中的节能措施探讨

以巢湖半汤国际温泉假日酒店暖通设计为例,分别从空调系统的划分,冷热源及输配系统的选择,空调末端系统的选择,以及热回收技术等方面对酒店暖通设计中的节能策略进行了分析和探讨。     

Dynamic buffering performance of the honeycomb paperboard filled with polyurethane

A new kind of composite buffering material was made by filling the voids of honeycomb paperboard with polyurethane. Drop tests were performed to evaluate the dynamic energy absorption capacity of the material. Based on the tests results, we analyzed the mechanical behaviors of the material under different conditions and obtained the inherent influencing laws of some factors on the material＇s dynamic buffering performance. It was shown that the dynamic buffering performance varied directly with impact velocity, and inversely with the void diameter, thickness and buffeting area of the composite material.     

Specific energy optimization in sawing of rocks using Taguchi approah简

This work aims at selecting optimal operating variables to obtain the minimum specific energy （SE） in sawing of rocks. A particular granite was sampled and sawn by a fully automated circular diamond sawblades. The peripheral speed, the traverse speed, the cut depth and the flow rate of cooling fluid were selected as the operating variables. Taguchi approach was adopted as a statistical design of experimental technique for optimization studies. The results were evaluated based on the analysis of variance and signal-to-noise ratio （S/N ratio）. Statistically significant operating variables and their percentage contribution to the process were also determined. Additionally, a statistical model was developed to demonstrate the relationship between SE and operating variables using regression analysis and the model was then verified. It was found that the optimal combination of operating variables for minimum SE is the peripheral speed of 25 m/s, the traverse speed of 70 cm/min, the cut depth of 2 cm and the flow rate of cooling fluid of 100 mL/s. The cut depth and traverse speed were statistically determined as the significant operating variables affecting the SE, respectively. Furthermore, the regression model results reveal that the predictive model has a high applicability for practical applications.