Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

井冈山水厂设计体会

阐述水厂设计中对水厂规模、水源地、净水厂位置及净水工艺的确定过程，根据原水的特点，通过分析对无阀滤池进行改良。     

Synthesis and characterization of poly(ethylene aspartate)-metal complexes

Poly(ethylene aspartate) [PEA] was synthesized by the melt condensation of D,L-aspartic acid and ethylene glycol. PEA containing pendent amino and carbonyl groups in its repeating chain was used as the polymeric ligand for complexation with transition metal ions, viz. Co(II), Ni(II), Cu(II), Mn(II), Zn(II), Cd(II), Ca(II), Mg(II), Pb(II) and Hg(II). Complexation was found to be most effective in DMSO. The resulting polyester-metal complexes were solid coloured materials which have been characterized by IR spectroscopy, elemental analysis and magnetic susceptibility measurements. The thermal stability of the polyester-metal complexes was investigated by thermogravimetric analysis (TGA). On the basis of the physico-chemical studies, an oxygen and nitrogen coordinated structure for the polyester-metal complexes is proposed.     

Liquid viscosities and densities of HFC-134a+glycol mixtures

Liquid viscosity and density of six binary mixtures of HFC-134a with glycols [ethylene glycol, diethylene glycol, triethylene glycol, polyethylene glycol (400), and polypropylene glycol (2000)] have been measured in the temperature range from 273 to 333 K. The viscosity was measured by a rolling-ball viscometer calibrated with standard liquids of viscosities and densities (JS5, JS10, JS20, and JS50). The density was measured with a glass pycnometer. The uncertainties of the measurements were estimated to be less than 3.4 % for viscosity and 0.04 % for density, respectively. An equation is given to represent the obtained viscosity values as a function of weight fraction and temperature.     

Probing the early stages of polymerization of ethylene on a model chromium/silica catalyst by Fourier transform infrared spectroscopy

The nature of the interaction of monomer, and the early stages of growth of oligomers of ethylene on a rather more uniform surface of Cr/SiO₂ catalyst than hitherto studied has been investigated by differenceFTIR spectroscopy using C₂D₄ and C₂H₄ as reactants both with and without subsequent treatment of the catalyst with CO andTHF. The active catalyst was prepared by reaction of vapour phase CrO₂Cl₂ with the vicinal hydroxyls of the silica surface. Three distinct kinds of methylene groups were detected. Arguments are given for assigning the peaks at 2935 and 2860 cm^–1 to CH₂ groups directly bound to the active site and those at 2920 and 2850 to CH₂s in the growing chain well removed from the Cr. The peaks at 2160 and 2165 cm^–1 are attributed to CD₂ groups hydrogen bonded to surface hydroxyls.     

Extraction of Anthocyanin Pigments from Purple Sunflower Hulls

The anthocyanin pigments in hulls of purple sunflower seeds were extracted using three solvent systems, 50:1:49 ethanol-acetic acid-water (EAW), 0.01M acetic acid (AAc), or water containing SO₂. Solvent, extraction time, size of ground hulls, pH of extracting solvent, hulls/solvent ratio, and concentration of SO₂ in water, were investigated. All were significant factors affecting yield of extracted anthocyanins. EAW and SO₂ were more effective extractants than AAc. Optimum conditions from response surface optimization for the extraction with sulphurous water were: SO₂ at 200 mg/L, hull size 20 mesh, extraction time 5 min at 22°C, and solvent/hulls ratio = 20.     

Mechanical and microstructure studies on the modification of CA film by blending with PS

DriedMusa paradiciaca (banana) stem and veins of the leaves, which were hitherto discarded as a waste, were collected and used as starting material for the preparation of cellulose and cellulose acetate. This cellulose acetate was mixed with polystyrene to form blend of cellulose acetate-polystyrene in order to provide enhanced stability and extended utility to the end products. The films of these composites or their individual partners were made separately and studied for their mechanical properties, chemical modification and morphological changes. We report here that banana stem is good source of cellulose and that cellulose completely undergoes modification upon esterification.     

Optimal size,hydraulic retention time and volatile solids loading rate of biogas unit using water hyacinth

With a view to evaluate the effects of hydraulic retention time and volatile solids loading rate on methane production using water hyacinth, experiments were conducted in a 160 dm³ capacity, well-mixed continuous digestion unit at ambient temperature. The optimal design of biogas plant using water hyacinth was elucidated, to provide a unit giving a maximum methane yield of 0.16 nm³ kg^?1 volatile solids added, which was 60% greater than the conventional plant using cowdung. The calculations of optimal design factors were based on reactor size, hydraulic retention time and volatile solids loading rate; considerations were made of capital cost, running costs and operational revenue.     

H9000 V4.0计算机监控系统技术特点概要

为了满足三峡右岸电站的应用需要,在H9000 V3.0计算机监控系统的基础上研制开发了H9000 V4.0系统,改进和完善了原系统已有功能,开发了新功能,进一步提高了系统的性能指标和可靠性指标。文中主要介绍H9000 V4.0系统的设计原则,以及数据采集、人机联系、报表定制、Web信息发布、历史数据管理等主要新功能。     

40000m~3/h空分设备主换热器的设计及制造

通过对进口 4 0 0 0 0m3 /h空分设备主换热器进行结构分析及对比模拟计算 ,用国产传热翅片进行设计、采用真空钎焊工艺制造的主换热器 ,经并网运行 ,设计指标优于原空分设备 ,为今后成套大型空分设备板翅式换热器国产化设计、制造创造了条件。