Frequency characteristics of stiffness and damping effect of ferro fluid bearing

Damping characteristics and frequency characteristics of ferro fluid bearing (FFB) spindles were measured using a high-frequency vibration base driven by a piezo actuator. Using the high-frequency vibration base, high-frequency excitation was added to ferro fluid bearing spindles mounted on the vibration base, and it was proved that ferro fluid bearing spindles have effective damping. And the damping effect became larger with higher spindle rotational speed. Also we have measured spindle runout of a ferro fluid bearing spindle using a lock-in amplifier to increase S/N ratio and succeeded to measure nano meter order displacements.     

Direct current bias applied to hot flame diamond deposition produces smooth low friction coatings

As-deposited diamond coatings generally have a high surface roughness which results in a high friction coefficient and extensive wear of the counter material in sliding contact. Therefore several methods for smoothening diamond coatings have been proposed, such as laser polishing, molten metal etching, thermochemical polishing and mechanical polishing. All these methods have some disadvantage e.g. long processing time or high processing temperature. Furthermore, they are all post-deposition treatments i.e. the manufacture of these coatings requires at least two processing steps, deposition and smoothening. With the present method which combines d.c. bias with hot flame diamond deposition, a smooth diamond surface is produced during the actual growth of the film. No post-deposition treatment is necessary. The surface roughness is not dependent on the coating thickness which means that thick coatings with smooth surface can be produced. In fact, the method has a smoothening effect, i.e. rough surfaces can be made smooth. The method is comparable to conventional hot flame deposition of diamond as to growth rate and cost of producing the coatings. The coatings have a nano-crystalline structure and a surface roughness of Ra = 25 nm, and result in a friction coefficient of 0.1 or less in dry sliding and about 0.05 in water-lubricated sliding against cemented carbide. Their wear resistance is virtually the same as that of conventional diamond films.     

考虑动作误差的低励限制与失磁保护定值配合方法研究

关于低励限制与失磁保护定值匹配的研究多聚焦于将其转换到同一功率平面或阻抗平面进行校核的方法,鲜有文献考虑实际装置动作特性对定值匹配结果的影响。该文从理论上详细分析各参数变化对失磁保护和低励限制的影响,提出基于装置动作误差的低励限制与失磁保护定值匹配校核原则,并论述定值失配时的定值调整方法,为当前各发电厂开展低励限制与失磁保护定值校核及整定提供了有效指导原则。     

B&WB-1950/25.41-M型超临界直流锅炉启动系统的调试

在介绍B&WB-1950/25.41-M型超临界直流锅炉启动系统构成的基础上,分析启动系统的调试情况,并对启动系统调试中发现的主要问题进行分析,并提出解决办法。     

电网短路电流限制技术探析

为提高系统运行的安全性及稳定性,降低故障大电流已成为一种迫切需求.文章首先介绍了当前短路电流的发展水平,并对现有的限流技术进行了概述,且简要分析了限流技术中各自的优缺点,最后对限流应用的未来提出了展望.     

采用DOE实验设计方法改进电容器级铌粉酸洗工艺

采用DOE实验设计方法,对制备电容器用铌粉的酸洗除杂工艺进行研究,确定了影响铌粉性能的关键因素是酸洗除杂工艺使用酸的浓度和酸洗时间。通过关键因素的全因子正交试验,对产品质量和工艺参数进行量化分析,确定最佳的酸洗工艺,可有效减低和控制电容器级铌粉中的主要C、O非金属及Fe、Ni、Cr金属杂质含量,降低电容器级铌粉的漏电流和损耗,提高电容器级铌粉的性能。     

同步电动机励磁系统的应用

采用由数字化控制技术单片机系统构成的BKL-501H微机励磁装置，对由发电机组构成的第一代同步电动机励磁装置进行改造，叙述了改造前存在的问题和改造后的特点。     

一个机组供电的晶体管稳流电源

1983年我们制作了一台由机组供电的晶体管稳流电源,取代原苏制BT-4稳流装置,作为ЭГ-2.5质子静电加速器分析磁铁的激磁电源。主要技术指标为:(1)额定输出直流电压100 V;(2)额定输出直流电流30 A;(3)电流调节范围0—30 A;(4)电流稳定度为±1.4×10~(-5)(当负载变化±10%时),±1.0×10~(-5)(当电网电压变化±10%时);(5)长时间漂移为2.3×10~(-5)/h,5.26×10~(-5)/8 h;(6)电流纹波为8.7×10~(-5)。     

一种带有泵升电容的新型高增益升压直流变换器

为了满足分布式发电系统中必须把太阳能、燃料电池和蓄电池输入的低压直流转换为高压的要求,在传统型升压直流变换器的基础上,提出了一种基于双电感和泵升电容的新型拓扑结构。该拓扑结构利用电感和电容的并联充电、串联放电特性,较好地实现了低占空比条件下高电压增益的目标。最后,分析了该拓扑结构在3种不同电感条件下的工作原理,并通过仿真验证了上述理论分析的正确性。     

电子式电流互感器高压侧自励源供能方法研究

介绍了一种直接从高压母线获取工作电源的电子式电流互感器结构方案,讨论了‘自励源’设计中的若干问题及应对策略,提出磁场取能方案中的限流‘漏斗结构’,给出了整机实验结果。