Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Dynamic photorheological analysis of photopolymerizable urethane dimethacrylate resins with varying diluent content and light fluence

The in situ measurement of dynamic changes in viscosity induced by illumination has been performed on a range of photosensitive urethane dimethacrylates (UDMA) evaluating the response at three different illuminations intensities (1, 2, and 5 W cm^?2) and at three different diluent concentrations (15, 30, and 50%), using 1,6‐hexanediol dimethacrylate (HDDMA). The initial viscosity value ranged between 1 and 10 Pa s for the mixtures with final viscosities approaching 1 × 10⁷ Pa s after illumination. The initial rise in viscosity was analyzed using an exponential model with an exponent ranging from 1.0 to 2.5 with time under exposure. Higher conversion rates were observed with both higher intensity and lower HDDMA content. The analytical approach taken here could aid in developing more sophisticated models that consider simultaneous flow and cure advancement in other thermosets. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Chromatic induction: Opponent color or complementary color process?

In present convention, chromatic induction (simultaneous and successive contrast) is usually held to be an opponent color process. Fifty years ago, it was an accepted complementary color process. The latter was never disputed yet apparently overlooked, and is here shown to be the more accurate account by inspecting afterimages and published data on simultaneous and successive hue induction. © 2007 Wiley Periodicals, Inc. Col Res Appl, 33, 77–81, 2008     

用常规电阻率测井资料确定水淹层的剩余油饱和度

油田综合含水越来越高，利用电阻率测井资料确定地层的剩余油饱和度变得非常困难。针对这一问题，提出了确定地层水民阻率和含油饱和度的方法。（１）利用已知的地怪水分析资料，采用井下自然电位刻度，井间对经和双自然电位一方法来示准地层水混合电阻率，然后利用相邻井相同地层的电阻率对比方法求含水饱和度。（２）利用电阻率的横向探测特性，避开阿尔奇公式中ｍ、ａ选择上的困难，采用横向法计算水淹层目前的含水饱和度。利用以     

基于公共存储器进行数据交换的高速数字图象处理系统

本文介绍了一种基于公共存储器进行数据交换的高速数字图象处理系统．给出了公共存储器的设计，描述了处理器对公共存储器的进程同步控制．     

Pultruded fibre reinforced polyurethane composites II. Effect of processing parameters on mechanical and thermal properties

This paper presents a novel process for the fabrication of pultruded polyurethane (PU) composites. The effects of the processing parameters on the mechanical properties (flexural strength and flexural modulus, etc.) and thermal properties (HDT) of the fibre reinforced PU composites by pultrusion have been studied. The processing parameters investigated include pulling rate (in-line speed), die temperature, filler type and content, and post-cure time and temperature. Results show that the composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio, the mechanical properties and the thermal properties of composites, the optimum die temperature can be determined. It is found that the mechanical and thermal properties increase with filler content for various types of filler. The mechanical and thermal properties increase at a suitable post-cure temperature and time. Furthermore, the properties which decreased due to the degradation of composite materials for a long post-cure time will be discussed.     

Saw and digital technologies in mutlicarrier demodulators

One key technology, for the implementation of future on-board processing payloads, is the multicarrier demodulator (MCD). The MCD is instrumental in allowing FDMA/TDM access schemes which optimize the use of on-board and ground resources in VSAT networks. This paper deals with the analogue and digital implementations of MCD, trying to assess the fields of application of each of the two technologies.     

Integration of knowledge-based systems with data processing

Transaction Oriented Prolog-Online Environment is a multi-user, mainframe implementation of the logic programming language Prolog, specially designed and developed for the data processing environment. This article describes the background, functionality, implementation and use of TOP-ONE, stressing that applications of knowledge-based systems technology to data processing environments will achieve full success only when existing systems and existing conventional data are incorporated within the applications.