Prediction of the effects on dynamic response due to distributed structural modification with additional degrees of freedom

The aim of this study is to investigate means of efficiently assessing the effects of distributed structural modification on the dynamic properties of a complex structure. The dynamic properties of the modified structure can be determined by experimental testing or numerical simulation, both of which are complex, expensive and time-consuming. Assuming that the original dynamic characteristics are already established and that the modification is a relatively simple attachment, the modified dynamic properties may be determined numerically without solving the equations of motion of the full-modified structure. The frequency response functions (FRFs) of the modified structure can be computed by coupling the original FRFs and a delta dynamic stiffness matrix for the modification introduced. The validity of this approach is investigated by applying it to a cantilever beam to which a smaller beam is attached as modification. The original FRFs were obtained experimentally as well as numerically. The delta dynamic stiffness matrix was determined numerically by modeling the attachment and part of the original structure including the attachment points. The FRFs of the modified beam were then computed. Good agreement is obtained by comparing the results to the FRFs of the modified beam determined experimentally as well as by numerical modeling of the complete modified structure.     

利用Love波特性计算地基动力响应

本文利用Love波弥散特性在频域上对地基出平面振动及扭振问题进行了研究。在计算区域内结构将采用有限单元划分,而在边界上则根据Love 面波特性使用传递边界有限单元。本文同时讨论了不同模态波对结构动力响应的贡献。本文方法也适合于静力分析。     

Discrete-time adaptive sliding mode power system stabilizer with only input/output measurements

In this paper a discrete-time adaptive sliding mode control method is newly developed and applied to the power system stabilization problem. A controllable canonical form of state space realization is constructed using the parameters identified by the on-line recursive least squares method and the system state is estimated from the input/output measurements and the simple state transformations. The identified parameters and the estimated state are then used by the discrete-time sliding mode control, which is suitable for the digital equipment. The most important advantage of the proposed power system stabilizer (PSS) is that it is able to maintain its regulating performance with a slower sampling period than that of the conventional sliding mode PSS because it is developed in a pure discrete-time domain. Another advantage of the proposed PSS is that it needs neither a mathematical model of the power system nor the full-state measurements because they are identified through on-line identifications. Several computer simulations for the linear power system are performed to verify the performance of the proposed PSS. In the computer simulations for various circumstances which are probable in a power system are considered, such as transitions of the active and reactive powers, change of parameters of the synchronous machine, line-to-ground faults and measurement noise. As a result, a new power system stabilizer which can operate in a wide range of operating conditions and can overcome various disturbances and measurement noises is proposed.     

特征线法分析长距离输油管道的流动瞬变过程

本文建立了基于特征线方法求充动瞬变过程的数值模型，编制了针对长距离输油管道流动瞬变过程的分析软件。在数值处理上，Ｄａｒｃｙ＝Ｗｅｉｓｂａｃｈ摩擦力项用二阶精度格式来近似，因此保证了高粘度流体在流动瞬变过程分析时的计算稳定性和精确度。模型考虑了埋管地形对沿线瞬变压力的影响，当某一泵站发生水击后其它站的反应同其上控程序确定。应用该软件，分析模拟了某一长距离输油管道在中间泵站停电或末站瞬时关阀情况下的流     

乙烯裂解炉辐射段流动与燃烧的三维数值模拟

用计算流体力学软件Fluent6.2对中国石油化工股份有限公司燕山分公司E-BA-107乙烯裂解炉辐射段内的流动和燃烧做了三维数值模拟研究。为保证计算的准确性,使用GAMBIT2.2软件建立了与裂解炉实际尺寸完全一致的几何模型;在计算过程中采用了标准k-ε湍流模型、离散坐标辐射模型和有限速率/涡流耗散燃烧反应模型等计算模型。通过模拟计算得到了裂解炉炉膛内的温度、烟气流速及烟气组成的分布:底部燃烧器和侧壁燃烧器的燃烧使附近的炉墙处于温度分布均匀的高温区,为裂解反应提供了均匀的辐射墙面;炉管底部比其他部位的温度低;底部燃烧器的高速射流产生的旋涡可为炉管提供一定的对流热;出口烟气的平均温度和组成的模拟计算值与设计值接近,表明数值模拟有较高的精度,具有实际意义。     

鼠笼式搅拌磨的流体场建模及计算机仿真

搅拌磨机在工业与研究领域是一种效率高的超细粉磨设备。为了优化设计参数，提高鼠笼式搅拌磨机的粉碎效果，需要对磨机研磨室内的流体场作深入的研究。利用Ansys有限元软件对鼠 式搅拌磨机研磨室的圆截面内的流体场进行仿真分析。通过对仿真结果的分析可知，在该流体场内存在着2个速度梯度较高的区域。在这2个区域中，粉碎作用明显。为了得到最佳的粉碎效果，应该使磨球尽可能地通过这2个区域。     

Optimal control of nonlinear systems to given orbits

Using optimal control techniques we derive and demonstrate the use of an explicit single-step control method for directing a nonlinear system to a target orbit and keeping it there. We require that control values remain near the uncontrolled settings. The full nonlinearity of the problem in state space variables is retained. The “one-step” of the control is typically a composition of known or learned maps over (a) the time required to learn the state, (b) the time to compute the control and (c) the time to apply the control. No special targeting is required, yet the time to control is quite rapid. Working with the dynamics of a well-studied nonlinear electrical circuit, we show how this method works efficiently and accurately in two situations: when the known circuit equations are used, and when control is performed only on a Poincaré section of the reconstructed phase space. In each case, because the control rule is known analytically, the control strategy is computationally efficient while retaining high accuracy. The target locations on the selected target trajectory at each control stage are determined dynamically by the initial conditions and the system dynamics, and the target trajectory is an approximation to an unstable periodic orbit of the uncontrolled system. A linear stability analysis shows that dissipation in the dynamical system is essential for reaching a controllable state.     

ON THE SLOW MANIFOLD CHARACTERISTICS OF CAPILLARY SUCTION APPARATUS DYNAMICS

The nonlinear dynamic behaviour relating the wet front size and liquid saturation under inner cylinder (or rectangular cell) in cylindrical (or rectangular) capillary suction apparatus was investigated. The slow manifold explanation was proposed and the fast- and slow-varying variables were identified. Experiments were conducted to verify theoretical findings.