改性纳米TiO2光催化降解苯酚活性的研究

在装有紫外光的光催化反应器中，用锐钛型纳米TiO2为光催化剂，进行了苯酚水溶液的光催化降解性能的研究。考察了溶液的pH值、纳米TiO2用量、镍（Ni^2＋）掺杂量、苯酚的初始质量浓度等因素对苯酚水溶液光催化降解过程的影响。结果表明，在pH值为7时，苯酚水溶液的降解率达95％以上，强酸和强碱条件均不利于苯酚的降解。当TiO2用量为50mg，UV辐照40min时，200mL质量浓度为50mg／L的苯酚水溶液的降解率为96．3％；当TiO2用量为150mg，UV辐照60min时，200mL质量浓度100mg／L的苯酚水溶液的降解率为95．8％。镍掺杂增加了TiO2的光催化活性，用质量分数为10％的二氯化镍水溶液掺杂制备的复合光催化剂，苯酚水溶液的降解率比未掺杂时增加13．6％。     

新型槽栅nMOSFET热载流子效应的模拟研究

应用二维器件仿真程序 PISCES- ,对槽栅结构和平面结构器件的特性进行了模拟比较 ,讨论了槽栅结构 MOSFET的沟道电场特征及其对热载流子效应的影响。槽栅结构对抑制短沟道效应和抗热载流子效应是十分有利的 ,而此种结构对热载流子的敏感 ,使器件的亚阈值特性、输出特性变化较大     

炼油厂碱性污水生物催化氧化预处理工艺研究

在对炼油厂碱性污水水质分析的基础上,提出采用生物催化氧化工艺对碱性污水进行预处理。试验结果表明,在水力停留时间为4 h,曝气量(标准状态)为8 m3／h的条件下,碱性污水的硫化物去除率可达90％以上,出水中的硫化物平均值为15．2 mg/L,CODCR、酚和油的去除率分别为47．5％,44．1％,50．8％,其中CODCR体积负荷为3．85 kg／(m3·d),是传统生化处理的10倍, 达到了污水预处理的目的。     

Environmental factors and kinetics of microbial degradation of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) in an aqueous medium

Environmental factors such as oxygen, temperature, and microbial species may have significant effects on decomposition of biodegradable polymers. A representative biodegradable, thermoplastic polymer, poly(3‐hydroxybutyrate‐co‐hydroxyvalerate) (PHBV), was decomposed in an aqueous medium under controlled laboratory conditions by soil microbes for the intrinsic degradation kinetics and the effects of the environmental factors on polymer biodegradation. The amount of proteins, including the PHBV depolymerases, that attached to the polymer surfaces was quite constant during the period of significant mass loss of the polymer specimens. The microbial polymer degradation followed a zero‐order rate model, so the residual mass fraction of PHBV films declined linearly with time. The mixed aerobic microbial organisms from fertile soil showed a higher activity of polymer degradation than an aerobic PHBV‐producing bacterium and the mixed anaerobes in the same soil. The mixed anaerobic microorganisms from barren soil decomposed the polymer at a slower rate than the anaerobes from fertile soil, and this was attributed to fewer microbial cells in the barren soil instead of the difference in the microbial species. The temperature effect on PHBV degradation can be described with an Arrhenius equation, and the activation energy is around 16 kcal/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 205–213, 2003     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.     

1H T2‐NMR monitoring of crosslinked polyolefin aging

This work examines the correlation between the ¹H‐NMR T₂ relaxation constant and the mechanical properties of aged crosslinked polyolefin cable insulation. T₂ experiments on unswollen samples could not differentiate between unaged and highly aged materials; all exhibited ¹H T₂ constants of approximately 0.5 ms. To accentuate the effects of aging, samples were swollen in various solvents. Unaged samples had T₂ values of approximately 15 ms in good solvents. With thermal aging, T₂ values decreased as the ultimate tensile elongation decreased. However, the correlation between T₂ and elongation differed for samples irradiated with high‐energy radiation and for materials aged above versus below the crystalline melting temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2578–2582, 2003     

深亚微米PD和FD SOI MOS器件热载流子损伤的研究

研究了深亚微米PD和FD SOI MOS器件遭受热截流子效应(HCE)后引起的器件参数退化的主要差异及其特点，提出了相应的物理机制，以解释这种特性。测量了在不同应力条件下最大线性区跨导退化和闽值电压漂移，研究了应力Vg对HCE退化的影响，并分别预测了这两种器件的寿命，提出了10年寿命的0．3μm沟长的PD和FD SOI MOS器件所能承受的最大漏偏压。     

氧化锌压敏电阻的老化机理

研究了ZnO压敏电阻的老化现象,提出了一种新的老化机理-线性链理论。该理论认为,在外电场作用下,压敏电阻势垒高度降低;当降低到一定值时,晶界可变电阻转化为线性晶界电阻,从而压敏链转化为线性链。线性链是稳定的,因而压敏电阻老化到一定程度后其电性能将不能完全恢复。     

聚合物降解产物伤害与糖甙键特异酶破胶技术

综述了钻井，完井，尤其是水力压裂作业中产生的多糖类聚合物伤害和应用糖甙键特异酶破胶，解除多糖类聚合物伤害的技术。第一节报道了聚合物降解产物造成的伤害，指出冻胶破胶液粘度低并不代表压裂液已从充填裂缝中充分返排，氧化破胶剂和普通酶破胶剂不能使多糖类聚合物充分降解，产生的大分子量，水不溶的降解产物可对地层造成伤害，消除伤害的办法是采用对糖甙键有特异性的各种水解酶作压裂液破胶剂或伤害地层处理剂。第二节报道了各种聚合物（纤维素，瓜尔胶，淀粉）糖甙键特异酶降解聚合物的机理。第三节报道了糖甙键特异酶（主要针对瓜尔胶）的应用性能测试及结果，包括岩心流动实验，含糖量和分子量测定，传导性测试。第四节介绍了糖甙键特异酶消除聚合物伤害和用作压裂液破胶剂的现场应用，包括选井原则，实施工艺要点及3个典型井例。     

邻苯二甲酸酯鼓泡生物降解

该课题测试了邻苯二甲酸酯类化合物的鼓泡生物降解行为。结果表明，邻苯二甲酸酯的降解速率常数（kb)与其烷基链长度之间存在良好的相关性，kb=0.0009x^2-0.019x 0.1123，相关系数r=0.9906；浓度超过500mg/L时，邻苯二甲酸二乙酯可抑制自身的生物降解；中间产物邻苯二甲酸浓度超过50mg/L时，也对邻苯二甲酸二乙酯的生物降解有明显的抑制作用。