试论我国解放后炼铁技术路线

本文简要回顾建国以来我国炼铁技术路线的演变过程，并展望２１世纪的前景。     

Strengthening technology and mechanism for semi-solid die casting of aluminum alloy

Combined with theoretical evaluation,an optimized strengthening process for the semi-solid die castings of A356 aluminum alloy was obtained by studying the mechanical properties of castings solution treated and aged under different conditions in detail,then,the semi-solid die castings and liquid die castings were heat treated with the optimized process.The results show that the mechanical properties of semi-solid die castings of aluminum alloy are superior to those of the liquid die castings,especially the strengthening degree of heat treated semi-solid die castingsis much greater than that of liquid die castings with the tensile strength more than 330 MPa and the elongation more than 10％,and this is mainly contributed to the non-dendritic and more compact microstructure of semi-solid die castings.The strengthening mechanism of heat treatment for the semi-solid die castings of A356 aluminum alloy is due to the dispersive precipitation of the second phase(Mg2 Si) and formation of GP Zone.     

变频开关电源Fuzzy-PID控制器的设计

针对感应式变频开关电源在对金属材料进行热处理过程中，负载的等效参数和谐振频率发生变化，而变频电源的输出频率不能及时调整和跟踪的问题，结合PID和Fuzzy控制技术的优点，设计Fuzzy-PID控制器对变频电源进行控制，在大偏差时用Fuzzy控制，在小偏差时用PID调节。Fuzzy-PID控制器以单片机8098为核心，采用SPWM专用芯片SA4828，实现变频开关电源的电压、电流双闭环控制，使变频电源不仅具有较快的动态响应、更小的超调，并且具有较高的稳态精度和频率跟踪控制特性。     

Determination of heavy metals and volatile aromatic compounds in used engine oils and sludges

Assessment of contaminant releases during utilization of used oils is essential for the determination of environmental acceptability. These paper reports the results of the study examining a toxic metal leachability from used engine oil and sludge samples employing leaching test (TCLP). The leaching test indicated that lead in oil samples exceeded 5-ppm concentration level what qualified them as a toxic waste. The samples of contaminated sludge were found to contain high concentration of total lead, barium and chromium, but the leaching test showed concentration below regulatory limit. The total content of benzene, ethylbenzene, toluene, and xylenes (BETX), and naphthalene in used oil and sludge samples was also determined and was found not to be a significant factor to contamination.     

木材用交联型醋丙胶粘剂的研制

研制一种由醋酸乙烯、丙烯酸丁酯、特种单体共聚而成的水性交联型环保胶粘剂以替代目前广泛使用的氨基树脂,适应绿色环保要求。     

Determination of the solubility parameter of poly(ethylene oxide) at 25°C by gas-liquid chromatography

The solubility parameter of poly(ethylene oxide) at 25°C has been determined using the method developed by DiPaola-Baranyi and Guillet, by the extrapolation of the values of the interaction parameter χ, at high temperatures, ranging from 70°–90°, 90°–110° and 110°–130°C down to 25°C. The values of the solubility parameter obtained, depending on the temperature ranges employed, are 9.8, 9.9 and 10.1, respectively.     

Some aspects of the analysis of coal by X-ray fluorescence spectroscopy

Bituminous coal samples from 84 distinct sources were analysed by conventional British Standards (BS) methods for phosphorus, sulphur, chlorine, ash and the ash-forming elements (calcium, silicon, aluminium, iron, sodium, magnesium, potassium, titanium and manganese). In most cases four determinations were made per element per source. Samples were crushed to ?212 μm (72 BS mesh) and pressed into aluminium cups at 20 t in^?2 (309 MPa) without binder or backing. Two pellets from each sample were analysed by wave-length dispersive X-ray fluorescence techniques, using a spectrometer equipped with a rhodium rube; the X-ray count took 60 s. The X-ray results were calibrated against the conventional results using multiple regression. The accuracy obtained was comparable with routine ‘wet chemical’ techniques. The X-ray technique is suitable for the routine determination of large numbers of samples.     

ON THE UNIMODALITY OF THE EXACT LIKELIHOOD FUNCTION FOR NORMAL AR(2) SERIES

Abstract. For stationary second-order autoregressive normal processes, the conjecture of uniqueness of the solution of the exact likelihood equations is examined. A sufficient condition for uniqueness is given; this condition is satisfied with very high probability if the number of observations is not extremely small. Moreover, it is shown that not more than two maxima may exist. Examples of data which actually produce a likelihood function with two local maxima are given.     

Properties of bioriented nylon 6 films related to film production technology

Four production steps, extrusion, blowing, stabilization, and finishing, are involved in the manufacture of biorented nylon 6 films. The films obtained after each step were studied by wide‐angle diffraction X‐rays, IR analysis, and density measurements. Orientation in the amorphous phase was evaluated by thermal retraction. Free volume was investigated by positron annihilation spectroscopy. Mechanical properties were tested by tensile tests, and permeability was tested with isopiestic permeameters. Quenching, after extrusion, generated an unstable γ crystalline phase and an amorphous phase. Blowing transformed the unstable γ phase into the thermodynamically stable α phase and increased the chain orientation; stabilization increased α phase crystals, favored hydrogen bond formation and, therefore, the mechanical properties, leaving unchanged the chain orientation; the final treatment increased the mechanical properties. The film permeabilities to O₂, N₂, and CO₂ were practically unchanged after each production step; this result may be explained by considering that the nanoholes, present in the films and responsible for the diffusion inside the polymer, maintained practically constant their radius, whereas their number concentration decreased slowly after thermomechanical treatments. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 559–571, 2002     

Thermodynamic Criteria for the Maximum and Minimum Strength of Fibre-Reinforced Composite Materials

The overall performance and reliability of composite materials are, in most cases, dependent upon the behaviour of the reinforcement-matrix interface, particularly upon its ability to transfer stress.

A theory for predicting thermodynamic conditions for the maximum and zero-adhesion at the reinforcement-matrix interface is tested in this paper, based on experimental data. Proposed is a model of the relationship between mechanical properties of composite materials (tensile strength, flexural strength, Young's modulus and impact resistance) and energetic properties of matrix and reinforcement expressed by the energy ratio a = γ_l/γ₂.