Al的添加对Gd-Co合金的影响

用X射线衍射、扫描电镜和磁性测量等方法研究了Al的添加对Gd-Co合金的影响。研究结果表明：在一定范围内掺杂Al导致GdCo2、GdCo5和Gd2Co17晶格常数增大，但仍保持各自的晶体结构；Al的添加使GdCo2和Gd2Co17的居里温度降低，但是对于GdCo2却是先增后减。该结论为寻找新的磁性材料提供了有价值的参考。     

Application of a Three-dimensional Wind Driven Circulation Model to Assess the Locations of New Drinking Water Intakes in Lake Ontario

A 3D transport model is used to perform a comparative analysis of several potential drinking water intakes located along the northwest shore of Lake Ontario between Toronto and Oshawa. The model is specifically used to assess each intake under both long- and short-term transport of a potential pollutant release from the Pickering Nuclear Generating Station and potential and actual pollutant releases from local land sources respectively. A model based on a 500 m grid resolution is calibrated using data collected in the aftermath of the 1992 tritium spill at the Pickering Nuclear Generation Station and subsequently used to simulate long-term transport. A model based on a 100 m grid resolution is verified using drogue studies and used to simulate short-term transport events. Both models are used to assess pollutant levels at each of nine potential intake locations under different wind scenarios and pollutant releases. Field data for the study included water quality and flow measurements from local sewers and rivers, and estimates of pollutant levels from the local waste water treatment plants. This paper describes the model setup for both the long-term and short-term transport models, calibration using field data, long-term transport modeling, short-term transport modeling, and the comprehensive analysis approach used to evaluate the nine potential intake locations proposed. Results indicated that four intakes in particular outperformed other intake locations by maintaining bottom pollutant levels within governmental standards and warning times that exceeded 20 hours.     

某跨线桥施工支架方案设计

结合某大桥的概况,根据梁体施工工艺要求、现场实地勘察情况确定跨线施工方案,支架采用布架灵活、搭拆方便、承载力大的WDJ碗扣式多功能钢支架,部分预应力现浇连续箱梁采用支墩加纵梁预留门洞的支架现浇,取得良好效果。     

PLC在环锭捻线机上的应用

介绍了如何使用PLC和数字变频调速技术 ,对传统环锭捻线机进行技术改造 ,使锭速、捻度和卷绕成形变换实现数字化柔性控制 ,扩大了工艺参数的变化范围 ,使整个捻线加工车间实现信息化管理成为可能。     

直接成像技术在PCB中的应用

电子产品日趋小型化、轻量化、多功能化，使电路板线路密度增加，从而对电路板的制作技术有了更高的要求，普通的接触曝光成像技术不能满足高密度电路的要求，激光直接成像（LDI）技术正迎合了精细线路的要求，而在PCB制作中得到应用。介绍了LDI的成像原理、存在的优缺点及其在PCB制作中的应用。     

Studies on nucleation kinetics of InxGa1−xN/GaN heterostructures

Nucleation kinetics during the growth of In_xGa_1−xN on a GaN substrate have been studied. The behavior of nonequilibrium between the In_xGa_1−xN and the GaN substrate has been analyzed, and hence, the expression derived for the stress-induced supercooling/superheating has been numerically evaluated. The maximum amount of stress-induced supercooling is found to be 1.017 K at x=0.12. These values are incorporated in the classical heterogeneous nucleation theory. Using the regular solution model, the interfacial tension between the nucleus and substrate and, hence, the interfacial tension between nucleus and mother phase and thermodynamical potential of the compounds have been calculated. The amount of driving force available for the nucleation has been determined for different compositions and degrees of supercooling. It has been shown that the value of the interaction parameter of InN-GaN plays a dominant role in nucleation and growth kinetics of In_xGa_1−xN on a GaN substrate. These values have been used to evaluate the nucleation parameters. It is shown that the nucleation barrier for the formation of a In_xGa_1−xN nucleus on a GaN substrate is minimum in the range of x=0.12 to x=0.17, and it has been qualitatively proved that good quality In_xGa_1−xN on GaN can be grown only in the range 0<x≤0.2.     

Determination of friction coefficient encountered in large deformation processes

A new technique, namely, the open-die backward extrusion test technique, was developed as an alternative method to the ring compression test in order to quantitatively evaluate the coefficient of friction, μ, at the die/workpiece interface. This technique relates the percentage deformation in height of the specimen to the percentage increase in extruded height of the specimen. In this study, the open-die backward extrusion tests (ODBET) were simulated for different aspect ratios, (H/D), and different die geometries, (d/D), by utilizing an elastic-plastic finite element code (ANSYS) in order to obtain the friction calibration curves (FCCs). The results indicated that the extruded height is related to the friction conditions at the die/workpiece interface. Therefore, ODBET can be used to generate FCCs to determine the coefficient of friction at the die/workpiece interface in large deformation processes.     

影响巨磁电阻钙钛矿锰氧化合物居里温度的结构分析

测定了La1-xAx(MnB）O3型巨磁电阻钙钛矿化合物在不同组成时的居里温度，利用A位离子对晶格能的贡献和B位离子极化力的变化分别对A和B位离子掺杂及A，B位离子组成同时变化时钙钛矿的居里温度进行了分析，结果与实验一致。     

基于图像灰度统计分布的高炉温度场动态定标算法

通过高炉红外图像建立料面温度场是判断高炉煤气流分布形态的一种有效方法,温度定标是建立温度场的基本问题之一.在高炉复杂、恶劣的环境下,本文以高炉十字测温为基础,通过热电偶温度数据和图像对应区域的灰度分布统计,动态地建立温度定标关系.算法具有较好的自适应性,实际生产运行表明,温度定标关系较好地适应了高炉炉况的不确定性,准确地反映了高炉温度场的变化情况.