平面近场测试系统在天线测试和诊断中的应用

介绍了天线近场测量的基本原理和HD-1型平面近场测试系统,并对近场测量在实际天线测试中的应用情况、发展方向和应用前景等作了简单的描述。     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

Effect of refraction on optical microscopic measurement of internal blood-vessel diameter and its correction

In optical microscopic measurement of internal blood-vessel diameters, the effect of refraction must be taken into account to ensure accuracy of the result. This effect is discussed and an analytical correction formula derived. Phantom blood vessels with known internal and external diameters were used to test the validity of the correction formula. The errors obtained prior to correction were reduced significantly after correction.     

The solution of the inverse problem of gravitational potential using a set of measurements of different field elements

A numerical solution of the inverse problem of the gravitational field at a single point is obtained using six field elements for a point, a spherical cap, a differential spherical sector and a vertical segment. In the system of six equations obtained, the unknowns are the mass of the body, the depth of its center, and the second, third, and fourth degree moments. The accuracy of the solution of this system is ten times higher than when using three field elements. __________ Translated from Izmeritel’naya Tekhnika, No. 5, pp. 3–8, May, 2007.     

Feasibility study of absolute activity measurement with metallic magnetic microcalorimeters

We report on a feasibility study on precise determination of mass-specific activity of low-energy emitting radioisotopes. Conventional methods of activity measurement suffer from source self-absorption and a strong decrease in detection efficiency for low-energy electrons and photons. We propose a new method based on metallic magnetic microcalorimeters with the source embedded in the detector target in a 4π geometry. First results with a ⁵⁵Fe source show that electrons and photons are detected with a detection efficiency close to unity and with little loss of energy for electrons. The aim of this study is to provide standards of activity with very low uncertainties in the framework of radiation metrology.     

纳米颗粒的测量与表征

介绍了用于纳米颗粒测量的电镜观察法、X射线衍射线宽法、激光粒度分析法、比表面积法、颗粒沉降法、扫描探针显微术以及小角X射线散射等,并对其测量原理、测量过程、适用范围及测量方法的优缺点进行了讨论。     

天津独流减河工程监控系统现地通信单元设计

提出一种配电网电容电流测量的新方法，在零序电压互感器的开口三角侧串联一个可调电感，通过注入一个变频恒流信号寻找配电网的谐振频率，改变可调电感的数值后寻找另一谐振频率，联立2个谐振方程求解电容电流，该方法消除了电压互感器漏抗对测量的影响。开发了配电网电容电流测量仪，经模拟试验和现场测试表明，该方法具有安全、快捷、准确等特点，适用于中性点不接地或经随调式消弧线圈接地配电网。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

工程项目中计量支付工作应注意的几个问题

从工程前期、中期计量支付、责权利协调方面对工程项目中计量支付工作进行了介绍，并对各阶段的工作注意事项作了说明，指出做好计量支付工作是控制工程项目建设的关键环节。     

Local Strain Measurement within Tendon

Abstract:  Tendon is a dense connective tissue, responsible for transmitting the forces generated by muscles to the skeleton. It is composed of a hierarchical arrangement of crimped collagen fibres, interspersed with proteoglycan matrix and cells, known as tenocytes. During physiological loading, tendons are subjected to strains in the region of 5–6%, which result in the straightening and realignment of the collagen fibres, generating variable local strain fields within the tendon. This study demonstrates a technique for analysing local strains within viable tendon explants, during both loading and unloading of the tissue. Samples were strained in a custom-designed rig, allowing real-time visualisation of cell nuclei, used as local discrete markers, on a confocal microscope. Results indicated that local strains within the fascicle are smaller than the applied strains, never exceeding 1.2%, even at 8% gross applied strain. By contrast, the sliding of adjacent collagen units was recorded at each strain increment in this study, reaching a mean maximum of 3.9% of the applied displacement. Loading–unloading studies indicated that sliding behaviour is reversible up to strains of 5%, and provides the major extension mechanism within the rat-tail tendon. This technique can be extended to further analyse shearing behaviour within the matrix.