Conducting composites of polythiophene and polyfuran with acetylene black

Conducting composites of polythiophene (PTP) and polyfuran (PF) with acetylene black (AB) were prepared via chemical oxidative polymerization of thiophene and furan in a suspension of AB in CHCl₃ at room temperature using anhydrous FeCl₃ as the oxidant. Formation of PTP and PF and their subsequent incorporation in PTP–AB and PF–AB composite systems were confirmed by FTIR analysis. Scanning electron microscope analysis showed the presence of compact clusters of particles in both composites. Transmission electron micrographs of PTP–AB and PF–AB composites showed formation of globular polymer encapsulated AB particles with average diameters of the order of ～100 nm in both systems. Thermogravimetric analysis revealed that the overall thermal stability varied in the order: AB > PTP–AB > PTP and AB > PF–AB > PF. DC conductivity values for the PTP–AB and PF–AB composites were of the order of 10^?2 and 10^?3 S cm^?1, respectively. Copyright © 2004 Society of Chemical Industry     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

The emulsifying properties of a polysaccharide isolated from the fruit of Cordia abyssinica

Polysaccharide was isolated from Cordia abyssinica and its effect, at differing concentrations, on its emulsifying ability was determined. Emulsions of vegetable oil containing up to 1% of the polysaccharide in phosphate pH 7.4 buffer, were prepared by using a hand piston homogenizer. Emulsification was assessed by diluting samples of the emulsions in sodium dodecyl sulphate and measuring absorbance at 500 nm. Addition of increasing concentrations of the polysaccharide up to 1% enhanced emulsification and emulsion stability. Above 1% concentration the polysaccharide solutions were too viscous for making emulsions conveniently. At a constant concentration of the polysaccharide, addition of up to a 1% concentration of salt enhanced emulsion formation. Further addition of salt above 1% resulted in no further changes in emulsifying ability, but the stability of the emulsions formed decreased on increasing the concentration of salt above 1%. The effect of pH on emulsifying ability was investigated by preparing emulsions using buffers of different pH, from pH 3 to pH 13. The polysaccharide had poor emulsifying ability below pH 7. Emulsifying ability increased with pH between pH 7 and 11. At pH above 11 there was a decrease in emulsifying ability.     

Photodegradation mechanism and stabilization of polyphenylene oxide and rigid‐rod polymers

Poly(2,4‐dimethyl‐1,4‐phenylene oxide) (PPO), poly(benzo[1,2‐d:5,4‐d′]bisoxazole‐2,6‐diyl‐1,4‐phenylene) (PBO) and poly(benzo[1,2‐d:4,5‐d′]bisthiazole‐2,6‐diyl‐1,4‐phenylene) (PBZT), which are polymers with extended conjugated structures, undergo a self‐sensitized photo‐induced electron‐transfer reaction. A second component is not required. This article presents many similar observations on these polymers when they are exposed to light and evidence to support the proposed photo‐induced electron‐transfer mechanism. Methods to stabilize these polymers against photo‐oxidation are also described. Workers investigating other conjugated polymeric systems may find the experimental methods, observations and polymer stabilization approaches discussed in this review useful. Copyright © 2005 Society of Chemical Industry     

Application of artificial neural networks to the analysis of two‐dimensional fluorescence spectra in recombinant E coli fermentation processes

A two‐dimensional (2D) spectrofluorometer was used to monitor various fermentation processes with recombinant E coli for the production of 5‐aminolevulinic acid (ALA). The whole fluorescence spectral data obtained during a process were analyzed using artificial neural networks, ie self‐organizing map (SOM) and feedforward backpropagation neural network (BPNN). The SOM‐based classification of the whole spectral data has made it possible to qualitatively associate some process parameters with the normalized weights and variances, and to select some useful combinations of excitation and emission wavelengths. Based on the classified fluorescence spectra a supervised BPNN algorithm was used to predict some of the process parameters. It was also shown that the BPNN models could elucidate some sections of the process's performance, eg forecasting the process's performance. Copyright © 2005 Society of Chemical Industry     

Modifizierung des ABSE‐Polycarbosilazans mit Multi‐Walled Carbon Nanotubes zur Herstellung spinnfähiger Massen

Modification of the ABSE polycarbosilazane with multi‐walled carbon nanotubes for the creation of spinable masses An inexpensive method has been found to produce ceramic SiCN‐fibres via the precursor route consisting of five processing steps: synthesis of the polymer, preparation of the spinning mass, melt‐spinning, curing via electron beam and subsequent pyrolysis at 1100 °C in a nitrogen atmosphere. A special solid and meltable fibre polymer, the so‐called polycarbosilazane ABSE, has been developed in the last decade for this purpose. Due to its low molecular weight, an adequate catalytic and thermal aftertreatment was necessary to guarantee a stable melt‐spinning process. This article discusses an alternative way to prepare a qualified spinning mass, i.e. the addition of Multi‐Walled Carbon Nanotubes (MWCNTs) to the ABSE melt. For this purpose a homogeneous dispergation of the MWCNTs in the ABSE matrix is necessary. In this study, spinning masses were fabricated in different ways. By optical analysis and comparison of the level of dispergation in these spinning masses an optimized process for integration of the MWCNTs was identified. The influence of the addition of a dispersing agent is investigated as well. In using a dispersing agent, the level of homogeneous dispersion of the MWCNTs increases whereas the interactions between the particles and the precursor melt decrease. In first spinning experiments a good spinability of the masses were noticed. Thus the addition of MWCNTs represents a new way to modify the ABSE precursor for the melt‐spinning process.     

Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.     

龙潭拱坝砼上坝运输方案选择

龙潭拱坝坝高９０ｍ，砼上坝运输是砼施工过程中的中间环节，控制进度的关键，必须因时因地制宜地选择适当的运输机械和运输方案，使砼运输能做到保质、保量、及时和经济，通过论证比较，结合本工程现实情况，砼上坝运输不采用缆机而采用门机方案．