推进石化销售企业质量管理创新发展

对照IS0 9001质量管理体系标推的要求，结合石化销售企业质量管理工作中存在的主要问题，提出质量管理工作创新的建议。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Bedload Transport in Alluvial Channels

Hydraulic, sediment, land-use, and rock-erosivity data of 22 alluvial streams were used to evaluate conditions of bedload transport and the performance of selected bedload-transport equations. Transport categories of transport-limited (TL), partially transport-limited (PTL), and supply-limited (SL) were identified by a semiquantitative approach that considers hydraulic constraints on sediment movement and the processes that control sediment availability at the basin scale. Equations by Parker et al. in 1982, Schoklitsch in 1962, and Meyer-Peter and Muller in 1948 adequately predicted sediment transport in channels with TL condition, whereas the equations of Bagnold in 1980, and Schoklitsch, in 1962, performed well for PTL and SL conditions. Overall, the equation of Schoklitsch predicted well the measured bedload data for eight of 22 streams, and the Bagnold equation predicted the measured data in seven streams.     

采用活性非均匀分布催化剂中变反应器的模拟计算

模拟计算表明:采用活性趋于表层的分布,可以较明显地提高国产中温变换催化剂的内表面利用率,有效地节省催化剂用量,而对“热点”温度没有多大影响。     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

镨掺杂分布对1.3μm光纤放大器特性影响

对掺氟化镨玻璃光纤放大器的小信号增益，用广义的高斯近似公式可获得精确的分析表达。文中研究了限制光纤芯层中央部分的镨掺杂对光纤放大器特性的影响，结果发现限制镨掺杂分布能改进光纤放大器的工作效率，且截止波长比芯层全部均匀掺镨的光纤更长。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

大型储罐的罐壁设计

根据十万立方米浮顶油罐罐壁板应力测试的实测结果，运用应力分析程序，对罐壁板应力分布情况进行了分析和比较，通过调整罐壁板的厚度，使新设计储罐的罐壁板应力分布更加均匀、合理。     

A method for multi-parameter PDF estimation of random variables

The probability distribution function (PDF) of a random variable Z is approximated with c·e^Q(z), where Q(z) is a polynomial function and c is normalizing constant. Based upon the weighted residual method, general linear algebraic equations have been derived for the evaluation of the unknown parameters in the polynomial. Numerical examples are presented and the results show that the PDFs obtained using the proposed method converge to those obtained from Monte Carlo simulation as the number of parameters in the approximate PDF increases.