基于时空的弱点状运动目标检测技术

如何在复杂背景下持续有效地检测目标位置,一直是研究者们需要面对的主要挑战。本文在研究红外点状移动目标特征的基础上,根据目标无纹理,无形状的特性,提出一种改进的形态学目标增强算法,并利用目标连续时空不变性检测目标。首先,建立多尺度的图像金字塔,在每层上采用改进的形态学算法快速、粗糙定位小目标。然后进一步的根据目标在时空上的位置相关性,提出基于目标运动特征分析的精确检测方法。得到精确稳定的检测结果。最后实验结果表明与经典的形态学检测算法及其他算法相比,该技术能更有效地检测弱小目标,具有更高的鲁棒性。     

基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。     

The use of bio-diesel based additive as rheology improver and pour point depressant of Nigerian waxy crude

The chemical method has proved to be the most effective mitigating method of wax deposition in petroleum system as it deals with the root cause of wax formation. Most of the commercial chemicals in the industry are very expensive and toxic. This paper aims the use of biodiesel based additives for improving the rheological behavior and pour points of waxy crude from Nigeria field. The biodiesels derived additives gave better performance than the commercial chemical and the seed oils as greatly improvement in rheology and pour point values of the waxy crude were observed     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

基于深度学习的人体姿态估计方法综述

基于深度学习的人体姿态估计方法旨在通过构建合适的神经网络，直接从二维的图像特征中回归出人体姿态信息。主要按照2D人体姿态估计到3D人体姿态估计的顺序，并从单人检测与多人检测、稀疏的关节点检测与密集的模型构建等方面，对近年来基于深度学习的人体姿态估计方法进行系统介绍，从而初步了解如何通过深度学习的方法得到人体姿态的各个要素，包括肢体部件的相对朝向和比例尺度、骨骼关节点的位置坐标和连接关系，甚至更为复杂的人体蒙皮模型信息。最后,对当前研究面临的挑战以及未来的热点动向进行概述，清晰地呈现出该领域的发展脉络。     

具有光照鲁棒的图像匹配方法

针对现有的基于局部特征的图像匹配算法对光照变化敏感、匹配正确率低等问题，提出一种具有光照鲁棒性的图像匹配算法。首先使用实时对比保留去色（RTCP）算法灰度化图像，然后利用对比拉伸函数模拟不同光照变换对图像的影响从而提取抗光照变换特征点，最后采用局部强度顺序模式建立特征点描述符，根据待匹配图像局部特征点描述符的欧氏距离判断是否为成对匹配点。在公开数据集上，所提算法与尺度不变特征变换（SIFT）算法、加速鲁棒特征（SURF）算法、"风"（KAZE）算法和ORB算法在匹配速度和匹配正确率上进行了对比实验。实验结果表明：随着图像亮度差异的增加，SIFT算法、SURF算法、"风"（KAZE）算法和ORB算法匹配正确率下降迅速，所提算法下降缓慢并且正确率均高于80%；所提算法特征点检测较慢和描述符维数较高，平均耗时为23.47 s，匹配速度不及另外四种算法，但匹配质量却远超过它们。对实时性要求不高的系统中，所提算法可以克服光照变化对图像匹配造成的影响。     

因素空间理论下基点分类算法研究

目前，基于因素空间理论的背景基提取算法计算过程复杂，初始化必须依赖各因素极值，基点数量提取冗余等原因，未能在应用中取得很好效果。为此，结合内点判别法和知识可继承、可扩展的思想，提出一种计算简单、初始化独立、基点数量小的改进的背景基提取算法。然后，利用改进的背景基提取算法构造出一种全新的数据分类算法-基点分类算法，基点分类算法以提取每一类样本的背景基为预测模型，再通过新定义的λ-背景基，优化预测模型。数值实验表明:基点分类算法原理简单、构造难度小、分类模型泛化能力强，预测能力准确率高，同时严格的模型限定区域又能为识别新类别提供新方法。     

简体接管边缘应力区局部减薄处应力特征

参考《压力容器定期检验规则》第40条,采用有限元方法计算了筒体接管边缘应力区局部减薄处的应力分布,得到了局部减薄处凹坑的尺寸与位置对应力的影响趋势,讨论了应力集中系数随尺寸变化的规律,为筒体接管边缘应力区局部减薄处的强度评定提供了一定的计算依据。     

离心泵并联运行工况点的数值求解

建立了求解多台不同型号离心泵并联运行工况点的数学模型,给出了用数值计算中的“二分法”求解该模型的方法,并附有用Exce l计算的实例。