Effects of surrounding brightness on visual search for safety colors

The present article reports the investigation of the effects of surrounding brightness on a visual search for three safety colors: red, orange, and yellow. Images of visual stimuli consisting of an array of colored circles placed on a large visual field (a visual angle of 40°) were displayed on an 80‐in. screen with a DLP projector. Experiment I examined the search efficiency under three levels of background luminance that were equivalent to the three target luminances. The results showed that the search efficiency for the orange target decreased as the number of distractors increased, under each of the background luminance levels, whereas the efficiency scarcely decreased for the red and yellow targets. Although a reduction in background luminance increased the search efficiency for the orange target, it is suggested that the effect of background luminance is smaller than the effect of the target color in search efficiency. Experiment II examined the search efficiency under three conditions of low levels of incident illuminance, which were matched with a linear regression to the luminance of color chips of safety colors measured twilight conditions. The results showed that the search efficiency for the orange target decreased as the number of distractors increased under each of the different illuminance conditions, whereas the efficiency scarcely decreased for red and yellow targets. Furthermore, as illuminance decreased, the search time for the orange target was more greatly impacted than for red or yellow. These results imply that the recognition of orange tends to be influenced by the surrounding brightness. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 400–409, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20152     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

变频调速技术在污水处理厂的应用

概述污水处理厂的一般工艺，简单介绍了风机、水泵等的节能特点，介绍了变频调速装置在污水处理厂各处理工段的应用。     

无线网状网技术与应用

无线网状网(WMNs)由网状路由器节点和客户机节点组成,其中的网状路由器节点组成了无线网状网的网络骨干,其移动性很小。他们一起为无线网状网和其他常规无线网络的客户机节点提供网络的无线接入。WMNs技术结合了中心式控制的蜂窝网与分布式控制的无线自组织网的优点,可有效克服这两种技术的缺陷并显著提高无线网络的性能,已经成为下一代无线通信网络的研究热点之一。WMNs可为无线个域网、局域网、校园网、城域网的一系列应用提供高速无线宽带接入服务。虽然目前WMNs技术发展很快,但其协议栈各层仍存在许多有待研究的课题。首先简要介绍了无线网状网的结构与特点;随后重点分析了其主要的几个应用领域;最后探讨了WMNs各协议层的研究现状与关键技术,并分析了该技术存在的问题及未来的研究方向。     

变频调速技术在济钢焦化厂高压氨水泵上的应用

济钢焦化厂高压氨水泵变频调速系统采用变频器和PLC相结合的方式 ,具有调速精度高、节能等多种功能 ,保证氨水泵正常工作。全年可增加经济效益 77.3万元。     

脆断事故的原因分析和预防措施

分析高强度材料和大型工程结构元件发生低应力脆性断裂的原因及条件，指出传统强度设计理论的局限性，从设计和工艺上提出防止发生低应力脆断事故的具体措施，给使用高强度材料和设计大型工程结构元件时提供参考。     

有限转角无刷力矩电动机位置伺服系统的电流控制

提出了有限转角无刷力矩电动机 (LABLTM)位置伺服系统电流控制策略 ,给出了实施方法 ,进行了开关管频率特性的分析。该方法可实现在不同误差时自动调节电动机电流 ,进而控制输出转矩 ,并具有稳态精度高、动态响应快等特点。     

Employment status passages and psychosocial well-being.

Medical students entering the labor market were studied to find out whether the improvement of psychosocial well-being depends on characteristics of their careers. Psychosocial well-being was described on the basis of psychosomatic stress symptoms, psychological distress (General Health Questionnaire), and strain resistance resources (Sense of Coherence). The 3-year follow-up showed that among women the improvement of strain resistance resources was delayed in the group with several entries into work. Among men the findings suggested associations between stress symptoms and career characteristics. Most of the results, however, did not support the hypothesis about the division of the participants into those with a stable career and improving well-being and those with a fragmented career and low well-being. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场