CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

聚酯的摩尔质量与机械性能研究——Ⅰ.动态力学性能

应用粘弹谱仪考察了不同摩尔质量的聚酯(PET、PBT、PBT/PET)的动态力学性能,结果表明摩尔质量增大将提高其模量,但亦导致结晶速度变慢,使测得的模量反而比摩尔质量较低的试样小.     

Numerical Analysis of the Constrained Blister Test

The constrained blister test is investigated through finite element analysis to determine the applicabilities and the limitations of the new technique. Numerical results confirm that the strain energy release rate asymptotically approaches a constant value. These results also show that the test technique and the approximate solution for strain energy release rate are applicable for some practical cases.     

Stochastic defect diffusion model for relaxation effects in crystalline polyethylene

It is suggested that some relaxation processes observed in crystalline polyethylene are consequences of the diffusive motion of a particular defect called a point dislocation or twist dispiration loop along the polyethylene stems in lamellar crystals. The motion of the defect, characterized by a diffusion coefficient and a mobility, is described by solutions of the Smoluchowski diffusion equation with boundary conditions that constrain the defect to move along routes that produce experimentally observable results. The fact that passage of the defect causes both a 180° rotation of the chain and moves an extra CH₂ group in the direction of the chain axis is important to the interpretation of the data according to this model. The diffusion coefficient for a defect is estimated to be around 2 × 10^?9 cm² s^?1 at 70°C. This value is shown to be reasonable both from the viewpoint of detailed computer modelling of defect motion and contemporary ideas about scaling.     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

生物质中元素分布特征的聚类分析研究

测定了稻草秆、小麦秆、玉米秆、棉花秆、大豆秆、玉米芯、花生壳和柳树、松树、桦树、杨树、杉树 1 2个农业生物质和林业生物质种类 2 7个样品中主要元素 K,Ca,Na,Mg,Al,Fe,P和痕量元素 As,Cr,Co,Cu,Cd,Mn,Mo,Ni,Pb,Ti,Zn,V,Si,Ba,Be,Se,Sb,Ge,Hg的含量 ,并用SPSS聚类分析法分别进行了 R型和 Q型聚类研究 ,对这些元素在生物质中的分布特征进行了研究 .结果显示 :杨木、杉木和桦木与松木和柳木归成一大类 ,经济类作物黄豆秆和棉花秆分别归类后又归入一大类 ;农业生物质稻草秆和小麦秆、玉米秆被归入一类 ;虽然 2 7种生物质样品分别取自我国东北、华东、华北和西南地区 ,在地理位置上相距极远 ,但样品聚类谱系图表明 ,元素的分布特征与生物质的种类的关系显著 ,与产地的关系不明显 ,即元素的分布特征受种类的影响大 ,而受生长环境、气候、土壤条件的影响小 .     

Mechanical behaviour of a combined joint composed of mechanical fastening and adhesive bonding

A study has been made of ‘combined’ joints consisting of mechanical fastening and adhesive bonding between rigid adherends. The mechanical characteristics of such ‘hybrid’ butt and lap shear joints have been derived by theoretical analysis. Results from experimental tests in combined joints giver reasonable agreement with the theoretical equations relating joint load to deformation.