射频MEMS压控电容器

研究了射频 MEMS压控电容器的设计和制造工艺。压控电容器的制作采用了 MEMS制造技术 ,其主要结构为硅衬底上制作金属传输线电极和介质层 ,然后制作金属膜桥作为电容器的另一个电极。通过改变加在金属膜桥与传输线间的电压达到改变电容值的目的。这种压控电容器可以工作于射频和微波波段 ,具有很高的Q值。测试结果如下 :在 1 GHz、0 V时 Q值达到 3 0 0 ,0偏压电容值为 0 .2 1 p F,当加上驱动电压后 Cmax/ Cmin的变比约为 4∶ 1     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

计算机辅助设计中浓淡曲线的设计

本文介绍利用Super Frame软件进行色彩浓淡设计的原理、方法和步骤。据此原理和方法,使用C语言设计开发出了应用实例——折线浓淡分布曲线。     

Electrochemical impedance spectroscopy of a free-standing oxide film

The corrosion of low carbon steel in natural sea-water is characterized by the formation and growth of compact and thick layers composed of oxides, insoluble salts and organic materials. These layers are the result of corrosion processes induced by local environmental conditions, water oxygen supply; ionic species; bacteria and organic matter. The exchange of various species (ions, molecules, gas) between sea-water and the rust layers or the metal depends both on the kinetics of the Faradaic reactions of the entities with either the oxides or the metal, as well as on their transport properties through the different strata of the rust layers. In this work, an impedance study was carried out using the 4-electrodes cell arrangement with corrosion products picked up on steel sheet piling immersed for 25 years and analyzed as free standing membranes. This new approach is a good way to reach the specific transport and transfer properties of the oxide without being blurred by the metal influence. The physical model developed in this work was based on a transmission line, and accurately described the experimental diagrams. The electronic resistivity of the oxide layer, its porosity, the mean pore size and the reaction kinetics parameters could be determined from the fittings.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

高职教育网上成绩考核系统的总体设计

本文对网上成绩考核系统进行了总体设计.其中,设计了校园网的网络结构模型、网上成绩考核系统的模块结构及其数据库和数据表.     

一种光时分制交换时隙分配计算算法

介绍了一种专为时分复用系统设计的时院分配计算算法。这种算法中主要用到的技术是从一个话务矩阵的各行选出一个区别代表的系统方法。对于任何话务矩阵，这种算法的分配效率都能达到１００％，所产生的模式矩阵个数最多为ｎ２－２ｎ＋２个（对于ｎ×ｎ矩阵）。     

中速球磨机运行中振动原因分析及消除措施

中速球磨机由于其独特的优点受到电厂的欢迎，但在运行过程中时有振动现象发生，影响了磨煤机及锅炉机组安全运行。本文根据磨煤体振动大与磨煤机电流的变化规律，针对ZQM-216型中速球磨机运行中的振动原因进行分析，并提出消除措施，以供同类型机组参考。     

Study on the propagation of inlet flow distortion in axial compressor using an integral method

 An integral method is investigated and developed in the current work. The effects of the parameters of inlet distortions on the trend of downstream flow feature in compressor are simulated. Other than the drag-to-lift ratio of the blade and the inlet incidence angle, it is found that the distorted inlet velocity is another essential parameter to control the distortion in propagation. Based on this study, a novel critical distortion line and corresponding critical distortion factor are proposed to express the effect of the two essential inlet parameters on the propagation of distortion, namely, the inlet incidence angle and the distorted inlet velocity. From the viewpoint of compressor efficiency, the propagation of inlet flow distortion is further described by a compressor critical performance and its critical characteristic. The results present a useful physical insight to an axial flow compressor behavior and asymptotic behavior of the propagation of inlet distortion, and confirm the active role of compressor in determining the velocity distribution when compressor responds to an inlet flow distortion. Received: 20 December 2001 / Accepted: 21 August 2002 The authors would like to thank HQ RSAF for permission to publish this work, their financial support and encouragement. The first author wants to acknowledge Prof. Frank Marble of California Institute of Technology, for bringing the problem to the author's attention and for his helpful discussion.