Crack initiation and propagation induced by inclusions in a nickel-base P/M superalloy under fatigue load

1 IntroductionRecently the key components in advanced aircraftengines are widely made of nickel-base P/M super-alloy. However, non-metallic inclusions are intro-duced into this material during powder metallurgyprocessing. In industry, although many method…     

Effects of can parameters on canned—forging process of TiAl base alloy（Ⅱ）——Mechanical behavior

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｉＡｌａｌｌｏｙｈａｓｌｏｎｇｂｅｅｎｃｏｎｓｉｄｅｒｅｄａｓａｐｒｏｍｉｓ ｉｎｇｍａｔｅｒｉａｌｆｏｒｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎ ,ｄｕｅｔｏｉｔｓｅｘｃｅｌｌｅｎｔｈｉｇｈｔｅｍｐｅｒａｔｕｒｅ ｐ     

单晶高温合金定向凝固过程中初生碳化物的上浮现象SCIEI

本文在一种抗热腐蚀单晶镍基高温合金平面及胞状液-固界面定向凝固条件下,发现了初生碳化物(TiC)的上浮现象并分析了其形成原因。     

高温精炼处理对铸造镍基高温合金组织与性能的影响

研究了高温精炼处理对铸造镍基高温合金组织与性能的影响.普通铸造镍基合金枝晶组织粗大,晶界碳化物呈链状分布,晶内碳化物呈草体汉字状密集分布于枝晶间,是合金塑性低的主要原因.经高温精炼处理后,合金的枝晶组织细化,晶界及枝晶间的碳化物数量减少,γ γ共晶相数量增加,晶界碳化物呈不连续质点状分布,晶内碳化物的密集程度下降,拉伸塑性和蠕变(持久)寿命得以明显提高.经1 650℃,5 min高温熔体处理后,合金室温延伸率由3.5%提高到9.2%,700℃高温塑性由2.0%提高到8.0%,900℃高温塑性由2.8%提高到9.6%,蠕变寿命由34 h提高到52 h,蠕变塑性由4.3%提高到6.11%.推荐的最佳高温精炼处理制度为1 650℃保温4 h.分析了高温精炼处理对合金液态结构、凝固组织与性能的影响机理.     

印制板化学镀镍

介绍了采用金属Zn粒子悬浮液活化要镀镍的印制板(PCB)Cu电路表面,使其可以进行化学镀镍的工艺方法,它可以克服Pd-Sn活化的缺点.     

NICKEL-BASED ALLOYS IN GE AIRCRAFT TURBINES：PAST,PRESENT ＆ FUTURE

1. Introduction Freedom to travel anywhere in the world, both quickly and inexpensively, defines our modern era. Despite year-to-year variation, the long term demand for travel by airplane continues to grow. Three ma- jor systems comprise the modern airplane: the aircraft structure that encompasses the fuselage, wings, and landing gear; the avionics that enable flight through crowded skies in nearly all weather conditions; and the propulsion system that powers the aircraft. Improvements in mat…     

Preparation of carbon nanotube composite material with metal matrix by electroplating

It is demonstrated that the nickel can be deposited directly on the surface of carbon nanotubes without pre-sensitization by Sn^2＋ and Pd^2＋ in a watt bath containing suspended nanotubes by electroplating. The nickel is deposited as spherical nanoparticle on the nanotubes. By increasing reaction time, the carbon nanotube is fully coated with nickel. A probable model, which represents the formation process of carbon nanotube-nickel composites by electroplating, is presented. The results show that this method is efficient and simple for preparing carbon nanotube-metal composite.     

面向对象的产品设计知识库的研究

文章立足产品设计知识库的功能需求分析,采用面向对象的方法构建产品设计知识库.首先,阐述了面向对象产品设计知识库的构建原理,也就是对产品设计知识抽象分类得到知识类信息并用专用的数据库进行管理,然后采取相应的程序接口生成知识管理的界面,并通过此界面完成产品设计知识的录入和其他管理工作.最后,文中接着简单介绍了面向对象产品设计知识库具体实现的几个重要方法.     

Oxidation Behavior of a Single-Crystal Ni-Base Superalloy in Air—II: At 1000, 1100, and 1150°C

The oxidation behavior of a single-crystal (SC) Ni-base superalloy was studied over the temperature range from 1000–1150°C and analysed by TGA, XRD, EDAX, and SEM. The results indicated that the SC Ni-base superalloy exhibited parabolic oxidation kinetics, which were controlled by the growth of the inner -Al₂O₃ layer. A mixed scale formed on the SC Ni-base superalloy after prolonged oxidation. The scale consisted of an outer layer of spinel, a sublayer of mainly -Al₂O₃ with small amount of spinel adjoined by a very thin and even discontinuous layer of CrTaO₄-rich oxide, and an inner -Al₂O₃ layer. The inner -Al₂O₃ layer provided good protection. No internal oxides or nitrides were observed below the inner -Al₂O₃ layer after 1000 hr at 1000°C, and after 200 hr at 1100 and 1150°C.