Optimal periodic forcing of nonlinear chemical processes for performance improvements

Unsteady-state periodic operations can improve the optimal steady-state performance of nonlinear chemical processes. To examine if the optimal periodic operation is proper and to obtain the optimal forcing functions subject to various control and state constraints it is suggested in this paper to convert the problems into a form which is suitable for constrained nonlinear programming. The adopted numerical optimization method is based on employing the control parametrization technique and is thus capable of dealing with the problem of multiple input forcings and obtaining optimal forcing functions and/or parameters while subject to general constraints. Besides, it provides information about to what extent the process performance can be improved by adopting the optimal periodic control.     

六维腕力传感器非线性正解耦方法设计

多维力传感器利用其多个转换单元完成测量加载于其结构上未知负载的作用效果,解耦是其设计的重要组成部分。针对传统静态线性解耦方法的不足,试图将传统线性解耦方程扩展为多项式结构,受其多元高次方式通解形式的启发,构造了一种多项式非线性静态正解耦方程,该方法无需传统线性解耦方法中的曲线拟合、逆解,不依赖以系统是线性为前提,且方程可以扩展成任意结构的多项式。实验结果表明:该方法能降低输出耦合误差。     

磁悬浮系统的控制方法研究

对于电磁吸浮型磁浮列车,悬浮控制是其关键部分,由于该系统的非线性和不稳定性,需要通过主动控制使其稳定悬浮。建立了磁悬浮列车悬浮系统模型,针对模型的非线性问题,采用精确反馈线性化将悬浮系统的非线性模型线性化,然后用闭环增益成形算法设计出非线性鲁棒控制器。用MATLAB的Simulink对具有扰动的非线性模型进行仿真,仿真结果表明控制效果没有静差和超调,调节时间快。     

Generic model control — A case study revisited

The application of the Generic Model Control (GMC) algorithm to the control of an evaporator has been reported recently by Lee et al. (1989). The results of their case study are claimed to demonstrate the superiority of the nonlinear GMC algorithm over conventional techniques including Dynamic Matrix Control. In this note it is shown that for the evaporator example the improved performance arises primarily from the full multivariable and feedforward nature of the control law, rather than from the nonlinear nature of GMC.     

Stability analysis and controller design of interval type-2 fuzzy systems with time delay

The type-2 fuzzy models can handle the system uncertainties directly based on the type-2 fuzzy sets. In this paper, the Takagi–Sugeno fuzzy model approach is extended to the stability analysis and controller design for interval type-2 (IT2) fuzzy systems with time-varying delay. Delay-dependent robust stability criteria are developed in terms of linear matrix inequalities by using the improvement technique of free-weighting matrices. Less conservative results are obtained by considering the information contained in the footprint of uncertainty. Finally, two simulation examples are presented to illustrate the effectiveness of the theoretical results. One is provided to show the merits of the proposed method, the other based on the continuous stirred tank reactor model is given to illustrate the design processes of IT2 fuzzy controller for a nonlinear system with parameter uncertainties.     

石油产品中硫醇硫含量测定的不确定度评估

根据国家标准GB/T1792-88《馏分燃料中硫醇硫含量测定法(电位滴定法)》的试验方法．考察评估了该项分析的测量不确定度。     

基于动力有限元分析和神经网络技术的含分层复合材料层合板的损伤诊断

本文基于作者提出的含层间分层损伤层合板的动力有限元分析模型和方法,计算了分层长度和位置对含层间分层损伤层合板结构的固有频率的影响,然后应用MATLAB的神经网络工具箱建立了人工神经网络,通过典型结构的仿真结果比较,证明了采用有限元动力分析和BP网络技术相结合的方法是一种可用于复合材料层合板的分层损伤诊断的有效方法.     

一类非线性随机时滞系统的故障诊断

针对一类非线性随机时滞系统提出了一种新的故障检测算法,该方法不同于传统的故障检测方法,是通过构建一种带有Consensus滤波器的故障诊断滤波器的方法来进行故障诊断.首先采用一组传感器测量系统实际输出,然后根据传感器的测量值构建一组残差生成器,将每个残差生成器看作一个小世界网络模型中的一个节点,采用动态Consensus算法计算出残差生成器的残差,并根据残差来判断系统是否有故障发生.仿真结果表明了本文所提出方法的可行性和有效性.     

Straightforward modeling of dynamic I–V characteristics for microwave FETs

This work presents a straightforward approach aimed at modeling the dynamic I–V characteristics of microwave active solid‐state devices. The drain‐source current generator represents the most significant source of nonlinearity in a transistor and, therefore, its correct modeling is fundamental to predict accurately the current and voltage waveforms under large‐signal operation. The proposed approach relies on using a small set of low‐frequency time‐domain waveform measurements combined with numerical optimization‐based estimation of the nonlinear model parameters. The procedure is applied to a gallium nitride HEMT and silicon FinFET. The effectiveness of the modeling procedure in terms of prediction accuracy and generalization capability is demonstrated by validation of the extracted models under operating conditions different than the ones used for the parameters estimation. Good agreement between measurements and model simulations is achieved for both technologies and in both low‐ and high‐frequency range. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:109–116, 2014.