场激活加压燃烧合成WC-Ni复合材料的工艺参数研究

以钨、碳和镍为原料,在电场激活下,材料的燃烧合成和致密化同时进行,短时间内完成了碳化钨镍复合材料的制备。研究了场激活 加压燃烧合成中的工艺参数,如脉冲电流、能量控制模式、升温速率、最高温度和压力对反应的影响。测量了在反应合成和致密化前后的样品 收缩率。所制备的复合材料的相对密度,490N载荷下Vickers硬度和断裂韧性分别为99.2%,13.965GPa和5.9MP·m1/2。     

温度场有限元分析的接缝单元

目前混凝土坝的仿真分析正从单坝段仿真向全坝仿真发展,因而需要采用接缝单元,笔者给出三种温度场接缝单元的计算模型：有限厚度接缝单元、近零厚度接缝单元及简化接缝单元.     

Electrical conductivity of ferroelectric sodium vanadate,rubidium vanadate,cesium vanadate and their solid solutions

The d.c. electrical conductivity of sodium vanadate, rubidium vanadate, cesium vanadate and their solid solutions sodium-rubidium vanadate and sodium-cesium vanadate were studied by a two-probe method in the temperature range covering their transition points. The electrical conductivity shows sharp change at the phase transition temperature of these materials. In NaVO₃, RbVO₃ and CsVO₃, increase in d.c. conductivity is observed in the ferroelectric region while nonlinearities are observed above transition temperatures. In solid solutions, the activation energy in the paraelectric state is higher than that in the ferroelectric state and depends upon sodium concentration.     

The solution of the inverse problem of gravitational potential using a set of measurements of different field elements

A numerical solution of the inverse problem of the gravitational field at a single point is obtained using six field elements for a point, a spherical cap, a differential spherical sector and a vertical segment. In the system of six equations obtained, the unknowns are the mass of the body, the depth of its center, and the second, third, and fourth degree moments. The accuracy of the solution of this system is ten times higher than when using three field elements. __________ Translated from Izmeritel’naya Tekhnika, No. 5, pp. 3–8, May, 2007.     

冲击噪声背景下的近场源二维参数估计方法

本文针对背景噪声为冲击噪声的情况,提出了一种新的近场源二维参数估计方法.本方法利用协变异(或协变异系数)构造矩阵,并通过求根的方法估计近场源的方向角和距离参数.该算法可以抑制冲击噪声对估计性能的影响,同时具有无需谱峰搜索的优点.仿真实验证明了该算法的有效性.     

百年欧式俱乐部——汉口西商跑马场调查纪实

通过对汉口西商跑马场的调查，说明它移植武汉的经过和历程，以及它在建筑设计方面的一些特点。     

Probabilistic analysis of a static frame model

This paper describes our efforts during our participation in the Sandia Validation Workshop. The focus of the paper is the calibration of material models and simulation of random fields to characterize the variations of material properties across spatial field. Both parametric and non-parametric methods were used to represent uncertainty. Part of the challenge of this problem is the small amount of data that is available for the necessary probabilistic analyses in support of calibration, validation, accreditation and prediction activities. The analysis methods and corresponding results are described.     

Effect of electric field on the hydrodynamics of fluidized nanoparticles

The effect of electric field on the hydrodynamics of nanoparticles was studied in a fluidized rectangular bed, with electrodes attached to two parallel walls. It was shown that the electric field of the order of 3 times the gravity markedly decreased the bed expansion and increased the solids volume fraction of nanoparticles fluidized by air. In these experiments, a light diode assembly was utilized to infer the local solids volume fractions within a rectangular bed of 10 nm silica particles. These experimental measurements yielded a two dimensional solids volume fraction distribution within the rectangular bed. The experimental results provided some new insights into the distribution of solids within the bed. The agglomerate diameters were computed using a momentum balance with the drag given by the Ergun equation and the empirical Richardson-Zaki method. Both methods yielded agglomerate diameters of the order of 100 μm and showed dependence on the strength of the electric field. The electric field decreased the granular temperature of the nanoparticles.     

俄罗斯减速器涡轮钻具驱动PDC钻头在西西伯利亚油田的成功应用

涡轮钻具由前苏联研制出来以后，得到了迅速发展，目前已发展到减速器涡轮钻具阶段。现在，俄罗斯西西伯利亚地区普遍使用减速器涡轮钻具钻井，而减速器涡轮钻具驱动PDC钻头的使用还是空白。采用俄罗斯生产的几种不同型号的减速器涡轮钻具，在西西伯利亚进行了驱动PDC钻头钻井的阶段性试验。试验结果表明，在优选PDC钻头结构的情况下，用减速器涡轮钻具驱动PDC钻头，钻头进尺和机械钻速都较牙轮钻头有显著的提高，经济和社会效益显著。介绍了试验中使用的3种俄罗斯减速器涡轮钻具(TPM-195，TPⅢ-195和TPO3—195)的结构特点和主要技术参数。     

克拉-2气田射孔工艺研究

克拉-2气田具有5大射孔难题:射孔井段长、地层压力大、产气量大、流体中腐蚀性物质和不宜丢枪,作业风险非常大。提出了带枪生产的射孔方案和射孔后取枪生产2种射孔方案,通过分析对比优选出最佳方案——最终选定模块式射孔枪过油管方案,并对该方案作了较为详尽的叙述,在后来的施工中成功地得到了印证。