Microstructures and Phase Transition Points of As-Cast Mg-Zn-Y System Alloys

As-east mierostruetures and their distribution of Mg-Zn-Y ternary alloy with high magnesium, low zinc and yttrium were examined using Nikon Epiphot optical microscopy （OM）, RigakuD/max-3C X- ray diffraetion （XRD）, and JEOL JSM-6700F scanning electron microscopy （SEM） equipped with an energydispersive X-ray spectroscopy （EDS）. In the as-east mierostructures, Yttrium and zinc tend to segregate at grain boundaries,     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

综合高速效应的凝析气藏流入动态

当井底压力低于露点压力时,凝析液在近井地带开始析出并不断聚集产生凝析油堵塞现象。因此,在制定凝析气井工作制度时,通常以控制生产压差为指导思想,往往忽略高速流动下凝析气液相变的非平衡特征。对于凝析气体系,当外界温压变化速度超过凝析气液的相平衡速度时,凝析气体系相变滞后,开始呈现非平衡特征,即凝析液的析出量随着压降速度的增加而减小。凝析气在向井筒流动的过程中,近井区高速流动使凝析气产生非平衡相变,凝析气在比较高的压降速度下流入井筒,使得凝析液来不及析出。在分析非平衡相变规律与近井地带凝析气渗流参数分布的基础上,评价凝析气液流动过程中的非平衡特征,给出了考虑非平衡相变的凝析液饱和度分布计算公式,并进行了产能预测结果对比。实例分析表明,可以通过适当放大生产压差,增加凝析气液相变非平衡特征,减小井筒附近的凝析液饱和度,提高气井产能与气藏开发效果。     

SO4^2-／ZrO2固体超强酸的制备及其催化合成ETBE的研究

采用沉淀一浸渍法制备了负载型SO4^2-／ZrO2固体超强酸催化剂，运用IR、XRD等方法表征所制备催化剂的物化性质。结果表明，所制备的催化剂具有固体超强酸催化剂的特征，酸性与焙烧温度有关，适当提高焙烧温度有利于样品酸强度的提高，但焙烧温度过高会导致脱硫；浸渍液H2SO4浓度高有利于提高催化剂的硫含量，但是浓度过高，会在催化剂上形成硫酸盐，从而降低催化剂的比表面积和酸性。采用制备的催化剂气相催化乙醇与叔丁醇合成乙基叔丁基醚反应，乙基叔丁基醚的选择性为54．71％。     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

CHAOTIC HYDRODYNAMICS IN HORIZONTAL GAS-LIQUID BUBBLY FLOW

ＮＯＭＥＮＣＬＡＴＵＲＥｄ———ｅｍｂｅｄｄｉｎｇｄｉｍｅｎｓｉｏｎ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＣｄ(ｒ)———ｃｏｒｒｅｌａｔｉｏｎｓｕｍ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＮ———ｎｕｍｂｅｒｏｆｐａｉｒｓｏｆｐｏｉｎｔｓｏｎｔｈｅｒｅｃｏｎ ｓｔｒｕｃｔｅｄａｔｔｒａｃｔｏｒ,ｄｉｍｅｎｓｉｏｎｌｅｓｓｒ———ｓｃａｌｉｎｇｄｉｓｔａｎｃｅ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＤｃ ———ｃｏｒｒｅｌａｔｉｏｎｄｉｍｅｎｓｉｏｎ ,ｄｉｍｅｎｓｉｏｎｌｅｓｓＫ———Ｋｏｌｍｏｇｏｒｏｖｅｎｔｒｏｐｙ ,ｂｉｔｓ/ｓＲ…     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

硅胶固载光敏剂的合成及其在反式维生素D3光敏异构化为顺式维生素D3中的应用

采用丙二酸作为连接,针9－蒽甲醇连接到硅胶上生成硅胶固载的光敏剂。利用此因相光敏剂分别在乙醇和甲苯溶液中敏化反式维生素D3。实验结果表明，此固相光敏剂能够有效地敏化反式维生素D3为顺式维生素D3的反应，并且非常容易从反应体系中分离出来。