掺染料激光介质的研究

以PMMA为基质，在助溶剂的作用下掺杂激光染料Rh6G制备出了塑料激光介质样品，采用YAG激光器作为泵浦源测试了塑料激光介质的发射光谱，讨论了其激光发射机理。     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

塑料布"V"形铺设法在水库引冰爬坡中的应用

通过塑料布“Ｖ”形铺设法在胜利水库引冰爬坡的应用与实践，证明了此法与传统贴坡式塑料布铺设法相 比，大大削减了冰推力对坝坡的破坏，减少了坝坡的修复费用，起到了良好的效果。     

激光在塑性变形测量中的应用

本文将激光应用于云纹法，研究了缺口滚压强化后根部区域的位移场及应变分布规律。结果表明，本方法是提高塑性变形测量精度的有效手段。     

废塑料裂化生产汽柴油工业化装置研究

报道了废塑料炼油工艺中连续法、间歇法、半连续法等各种方法的特点 ;重点对各工业化流程中存在的问题和解决的方法进行了讨论 ,并提出了一些合理化的建议。     

高层钢-钢骨混凝土混合结构的设计研究

结合一幢高层钢 钢骨混凝土混合结构的设计 ,着重介绍了在罕遇地震作用下采用层模型和空间模型的弹塑性分析计算结果、钢骨混凝土柱与钢梁的计算、节点设计及相应的构造措施 ,供结构工程师参考。     

Analysis of crack tip plasticity for microstructurally small cracks using crystal plasticity theory

Crack tip plastic zone sizes and crack tip opening displacements (CTOD) for stationary microstructurally small cracks are calculated using the finite element method. To simulate the plastic deformation occurring at the crack tip, a two-dimensional small strain constitutive relationship from single crystal plasticity theory is implemented in the finite element code ANSYS as a user-defined plasticity subroutine. Small cracks are modeled in both single grains and multiple grains, and different crystallographic conditions are considered. The computed plastic zone sizes and CTOD are compared with those found using conventional isotropic plasticity theory, and significant differences are observed.     

Homogeneous Plastic Flow of Fully Amorphous and Partially Crystallized Zr_(41.2)Ti_(13.8)Cu_(12.5)Ni_(10)Be_(22.5) Bulk Metallic Glass

The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amo     

Diffusion in metallic glasses

Rutherfordα-particles backscattering technique was employed for measurements of diffusion rates in metallic glasses. Effects of relaxation, crystallization and plastic deformation on diffusion rates were also investigated. It has been observed that the diffusion rates of a metallic solute are of the same orders of magnitude in both metal-metal and metal-metalloid glasses. A higher diffusivity is likely if there is a large difference between melting points of the solute and matrix. Relaxation has no effect on diffusion, however, diffusivity increases on crystallization. An increase in diffusivity is also observed on plastic deformation of metallic glass.     

Filler-induced failure mechanism in plastic-encapsulated microelectronic packages

Based on empirical data, the present work provides a model to prevent filler-induced reliability degradation in plastic-encapsulated LOC (lead-on-chip) packages. According to the model, the maximum size of the silica fillers included in the plastic package body should be smaller than one half of the inter-distance between the device and its overlying lead-frame. In particular, it is shown in the model that the spherical silica particles, which are sometimes trapped in the space between the top surface of the device and the bottom of the lead-frame during the encapsulating process, can induce huge compressive stress on a specific site of the integrated circuit pattern due to the thermal shrinkage of the plastic package body. Further, the present model suggests that tiny fillers squeezed beneath a large trapping filler might directly attack the brittle layer of the device pattern because the compressive force from the large filler particle can develop into huge compressive stress due to the reduced load-carrying area.