Evaluation of a proper controller performance for maximum-power point tracking of a stand-alone PV system

In this paper the implementation of a suggested stand-alone PV system, for maximum-power point tracking (MPPT), is carried out. Also, this paper presents a comparative study, through experimental work, between the conventional PI controller and the fuzzy logic controller (FLC) under different atmospheric conditions. The implemented system with both the PI controller and the FLC gives a good maximum-power operation of the PV array, but the tracking capability for different optimum operating points is better and faster for the case of using the FLC compared to the case of using the PI controller.     

微型构造表征技术在八面河油田的应用

通过对八面河油田井网密集区及井网稀疏的欠开发区的微构造研究,探讨了微构造表征技术。首先在储层多层次逐级对比的基础上,建立主力油层对比关系;密集井网条件下,则利用钻井资料编制油层顶底微型构造图;对于欠开发地区,通过人机联作自动追踪成图技术,输出2m等值线间隔构造图,建立微构造模型。以微构造模型为基础进行潜力评价,部署关键井寻找优质储量或进行开发动态调整。应用该项技术在八面河油田滚动发现了角15块等断鼻翼部局部高点,增加石油地质储量488×10~4t。     

Influence of numerical and viscous dissipation on shock wave reflections in supersonic steady flows

Numerical simulations are investigated to describe precisely the shock wave reflections in supersonic steady air flow field. The main objectives are to study the influence of the wedge trailing edge corner angle, of the numerical methods and of the viscous effects on the shock wave reflections and on the hysteresis behavior. The computations are done with different MUSCL-TVD finite volume schemes and the corresponding results are compared. The flow viscosity is also taken into account and comparisons are made between inviscid and viscous flow simulations. The results display the non-negligible influence of the numerical scheme accuracy on the results, mainly on the position and height of the Mach stem, and the relatively weak influence of the flow viscosity on these parameters. Comparisons between numerical results and experimental data have also been done and a good agreement is only observed for small wedge angles mainly due to the three-dimensional effects in the experimental setup.     

SBR工艺发展应用综述

关于SBR工艺的书籍和文章很多。本文在这些资料的基础上整理总结 ,对经典SBR工艺的应用进行了综述 ,归纳了经典SBR工艺的特点 ,介绍了各种新型SBR工艺。     

复合内衬在燃油加热炉中的应用

对导热油加热炉炉壁温度升高的原因进行了分析,介绍了新型复合内衬的特点,并对其技术特点、施工工艺及应用效果进行了简单阐述。     

基于轮廓线匹配的二维重迭物体的识别

本文提出一种基于轮廓线匹配的二维重迭物体的识别算法,并采用一种点模式匹配的快 速算法进行特征点序列的匹配,通过引进形状移位数的概念和利用问题中的各种约束条件,提 高了物体识别速度.     

钨金属化与氧化铝陶瓷高温共烧

阐述了钨金属化与氧化铝陶瓷高温共烧工艺的特点,分析了烧结过程中温度曲线和露点等工艺参数对钨金属化与瓷件结合强度、密封气密性和收缩率的影响。通过反复的试验和烧结机理分析对比,给出了最佳的控制参数。     

HPD-2型非临氢降凝催化剂工艺实验

利用HPD-2型非临氢降凝催化剂进行了中试实验。结果表明：HPD-2型非临氢降凝催化剂相对其他的同类催化剂产品液体收率较高，最高可达95％以上；在反应温度为380℃时，凝点降幅在50℃左右，降凝效果较好；产品性质稳定，具有很好的应用前景。     

PVT Measurements on tetrafluoroethane (R134a) along the vapor-liquid equilibrium boundary between 288 and 373 K and in the liquid state from the triple point to 265 K

For the investigations of the gas-liquid phase equilibria, a new apparatus has been developed capable of simultaneously determining the pressure and the liquid and vapor densities using Archimedes' principle. The relative measurement uncertainties of the liquid and vapor densities of R134a (purity, 99.999%) at 313 K are 2×10^–4 and 7×10^–4, respectively (95% confidence level). For the measurements in the liquid region along nine quasi-isochores at pressures up to 5 MPa, an isochoric apparatus was used. The relative measurement uncertainty ofpv/(RT) is less than 1×10^–3. In addition to the investigation of the (p, v, T) properties, the temperature and pressure at the triple point and the vapor pressure between the triple point and 265 K were measured. On the basis of these data, a vapor pressure correlation has been developed that reproduces the measured vapor pressures within the uncertainty of measurement. The results of our measurements are compared with a fundamental equation for R134a, which is based on the measurements of other research groups.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.