大颗粒尿素造粒工艺简介

介绍了大颗粒尿素造粒工艺，着重介绍了荷兰NSM公司的流化床造粒技术和法国K－T公司的流化床转鼓造粒（FDG）技术。     

几种重要的有机氯系阻燃剂

介绍了氯化石蜡、氯化聚乙烯、四氯邻苯二甲酸酐、四氯双酚A、六氯环戊二烯 及由六氯环戊二烯衍生的几种氯系阻燃剂的生产过程和用途。     

浅论国内大中型磷铵装置技术改造路线的选择

简述国内磷酸二铵的建设情况及不同的生产工艺、原有磷酸二铵装置改造选用的工艺及生产情况 ,重点介绍 Incro工艺在云南红河州磷肥厂年产 12万吨磷铵装置中的改造情况 ,经过比较认为原采用预中和槽流程磷酸二铵装置增产改造时选用 Incro工艺比较合适     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

0.89dtex细旦涤纶短纤维工艺优化探讨

介绍了纺制 0 89dtex× 3 8mm细旦涤纶短纤维的工艺技术特点 ,着重讨论了熔体温度、纺丝速度、冷却条件等工艺对原丝性能及产品质量的影响     

电算法在液压支架受力分析中的应用

建立支架受力分析的电算设计数学模型并给出程序框图     

挠性胶管的阻尼减振机理初探

建立了挠性胶管阻尼耗能的简化模型。以此为基础分析了挠性胶管的阻尼耗能的一般规律,并得出了一些新的结论。     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

舰船水声隐身技术(二)

本文探讨了水声隐身性能对舰船战技术性能的影响 ,舰船水噪声的主要噪声源、水噪声的治理措施及其展望。     

Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.