1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。     

溶胶-凝胶生物玻璃多孔材料显微结构和生物活性的扫描电镜及红外光谱分析

本文利用溶胶．凝胶法制备了CaO-P2O5-SiO，系统生物活性玻璃，并以其为原料制备了用于骨修复及骨组织工程支架的块状生物活性材料。利用体外实验方法(invitro)结合x射线衍射(XRD)、扫描电子显微镜(SEM)和傅立叶变换红外光谱分析(FTIR)技术对不同烧结工艺制备的材料结构、晶相和生物活性的影响进行了分析研究。研究表明，经800℃和1100℃烧结5min的两种材料均有硅磷酸钙Ca5(PO4)2SjO4微晶相析出。烧结温度越高，析出微晶相的体积比例越大，材料的生物活性则越低。在模拟生理溶液中碳酸羟基磷灰石(HCA)只在烧结体中的玻璃颗粒表面形成，而在其硅磷酸钙Ca5(PO4)2SiO4微晶相表面未发现HCA形成。     

Determination of polymer–polymer interaction parameters using inverse gas chromatography

A modified method is discussed that is based on Farooque and Deshpande's method to obtain polymer–polymer interaction parameters using inverse gas chromatography (IGC) data. In the Farooque and Deshpande method, the ratio of the difference of probe–polymer interaction parameters between two polymers and the probe volume [(χ₁₂ ? χ₁₃)/V₁] is used as the abscissa. In the modified method, the ratio [(?₂χ₁₂ + ?₃χ₁₃)/V₁] is used as the abscissa. Experimental data previously reported for a poly(?‐caprolactone)‐polyepichlorohydrin (PCL/PECH) blend and a poly(ethyl acrylate)‐poly(vinyl propionate) (PEA/PVPr) blend are analyzed. It is found that the slopes obtained by the new method had smaller deviations from the theoretical values than the Farooque and Deshpande method. The standard deviations of both slopes and intercepts obtained from the new method are also smaller. Using the new method, the polymer–polymer interaction parameters obtained from the intercept are negative numbers for the PCL/PECH system and very small positive numbers for PEA/PVPr. Explanations are given for the probe and concentration dependency of the polymer–polymer interaction parameters that are generally observed in IGC studies. A new method for selecting the best probe for calculating the interaction parameter is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 671–680, 2003     

支持下一代无线宽带应用自适应QoS模型的研究

作为真正完整的下一代网络 ( NGN,Next Generation Network)解决方案 ,NGN需要在固定通信领域和移动通信领域都能够支持综合多媒体特性。NGN中的新一代移动通信网承载在开放式、层次化结构的分组交换网络之上 ,能够为用户提供端到端的 Qo S解决方案。本文分析了下一代移动通信系统中多媒体宽带应用的 Qo S问题 ,从无线通信系统的多层次结构出发 ,建立了业务流的 Qo S指标评判体系 ,为下一代网络中的无线宽带应用提供了一种自适应Qo S控制模型     

Effect of organic dopants on electrodeposition and characteristics of polyaniline under the varying influence of H2SO4 and HClO4 electrolyte media

Electrodeposition of conducting polyaniline (Pani) was made under potentiostatic condition at pH 1.0 in different electrolyte media (H₂SO₄ and HClO₄) in the absence and presence of two organic dopants, disodium salts of naphthalene-1,5-disulphonic acid (NSA) and of catechol-3,5-disulphonic acid (CSA). The rate and yield of Pani deposition were dependent on the acid medium and the dopant employed. NSA in H₂SO₄ caused an increase in rate and yield but CSA decrease when compared to the rate and yield of H₂SO₄ alone. In HClO₄ medium, both the dopants showed a decrease. With regard to DC electrical conductivity, both the dopants exhibited an enhancement in H₂SO₄ medium but NSA a decline in HClO₄. Characterisation of the electrosynthesised polymer samples by various instrumental techniques (cyclic voltammetric: CV, FTIR, UV-Visible: UV-Vis, EPR, XRD, TGA and DTG methods) revealed that between the two acid media, H₂SO₄ was the better one. Further, it enlightened the role of two organic dopants in relation to the acid media. The advantageous role of NSA in H₂SO₄ had origin on its molecular characteristics such as non-polarity, larger π-electron cloud etc., while CSA could not perform such a role because of its easily oxidisable hydroxyl groups. In HClO₄, however, both the dopants could play only an unfavourable role owing to its greater polarity and oxidizing power than H₂SO₄.     

国际检验方法对促进产品质量提高的启示

对氨基二苯胺是性能优异的对苯二胺类防老剂的中间体。其质量好坏直接关系到防老剂4020、4010NA、688等品种的质量。对氨基二苯胺质量检验方法的提出则有助于我们开拓思路，更新质量观念，地症下药，分析原因，采取措施，全面提高其内在质量。     

聚氨酯-聚丙烯酸酯共聚乳液的成膜和性能

通过XPS和接触角测试研究了聚氨酯-聚丙烯酸酯共聚乳液在不同基材上的成膜情况，并对共聚胶膜的耐水性和附着力进行了考察．由于该共聚乳液同时存在着亲水组分和疏水组分，所以它在不同的基材上成膜可导致其膜表面的组成成分不同，因而导致其耐水性和附着力也随基材而异。结果表明，亲水性的聚氨酯组分均富集于胶膜内部，但胶膜底层聚氨酯组分的含量却随基材的不同而不同。在憎水且表面张力较高的基材上，共聚胶膜的耐水性良好；共聚胶膜的附着力在表面张力较高的基材上也良好。     

用环氧厚浆涂料防混凝土碳化

介绍了针对早期建筑的混凝土桥梁碳化情况采用H52-S4环氧厚浆涂料进行封闭保护、防腐处理的施工方法及施工工艺，并提出施工中应注意的有关事项，对温度影响、表面气泡处理进行了讨论，提出合理化建议。     

双自由度后坐保险机构的计算机动态仿真

在Workin Model 3D软件上对引信的双自由度后坐保险机构进行了有关计算机仿真计算，并结合具体实例进行了优化设计。     

未来航空润滑油基础油

介绍了未来航空涡轮发动机对润滑油性能的要求:在260,-54℃时,试样运动黏度分别大于1.0 mm2/s和小于15 000 mm2/s,热氧化安定性温度为260~427℃。该要求已超出了目前使用的酯类润滑油所能承受的最大极限。为了满足要求,需开发全氟聚醚、改性硅油、聚苯醚、C-型醚、氟醚三嗪及环三磷偶氮润滑油基础油,它们的使用温度依次为:-34~316,-60~260,5~288,-29~260,-30~343,-15~343℃。