合成彩色立方氧化锆的宝石学特征

市场上出现的紫色、浅紫色、浅黄色、粉红色、酒黄色、黄褐色、红色人造立方氧化锆均为亚金刚光泽, 火彩明显; 密度为5.99～6.34 g/cm3, 相对硬度为8～9; 除粉红色者表现出非均质性和弱多色性且内含大量定向排列的白色脱溶物外, 其余的为均质性, 内部洁净; 不同颜色的立方氧化锆的吸收光谱、紫外荧光以及滤色镜下的变色情况均存在差异; 浅紫色立方氧化锆的吸收光谱特征表明它是Nd致色. 能谱分析结果表明: 彩色立方氧化锆的常见元素有Zr, Y, P, Hf, Ca等; Er, Ce, Fe分别是粉红色、红色、酒黄色立方氧化锆的致色元素; 当Y2O3的摩尔分数大于或近于7%时, 立方氧化锆为立方面心结构且内部洁净; 当Y2O3的摩尔分数小于5%时, 立方氧化锆表现为非均质性且内含大量定向分布的白色脱溶物. 用拉尔森改写的格拉斯顿-代尔公式计算其近似折射率为2.12～2.19.     

基于DFT插值的宽带波束形成器设计

本文提出一种基于DFT插值的宽带波束形成器设计方法。首先推导了具有频率不变波束图的连续线阵的灵敏度函数与离散线列阵加权系数之间的关系；接着给出了基于DFT插值的宽带波束形成器设计的两个步骤：（1）使用窄带波束形成器的设计方法计算在参考频率下基阵的加权系数；（2）根据参考频率下基阵的权系数与其它子带权系数之间的关系，利用DFT插值的方法求出其它子带的加权系数。最后，给出了一个设计实例说明本文方法的有效性。     

数值地形图的生成及其水文地貌特征评价

数值地形图(DEM)是利用地理信息系统(GIS)进行流域水文模拟的基础, 其精度直接影响模拟结果在没有现成的数值地形图时, 应用人员往往利用传统的地形图来生成它. 本文分别采用Arc/Info地理信息系统软件提供的哈奇逊法和不规则三角网五次插值法, 对一个实验流域的高程取样点进行插值, 生成了4种不同的数值地形图, 从凹洼分布、流域界定、河网提取、地面坡度和地形指数、以及地面径流汇成等方面, 对它们的水文地貌精度进行了比较. 结果表明, 两种方法都能生成由高程点群所反映的地形, 然而由于哈奇逊法能够结合流域的河网结构及其具有物理基础的水文地貌加强法来处理凹洼问题, 因此大大地提高了其所生成的流域数值地形图水文地貌特征精度.     

带有给定切线多边形的保形有理三次B样条曲线

本文给出了带有给定切线多边形的保形有理三次Ｂ样条曲线，其部分权因子可通过选取切点的位置来确定，由此方法还导出了保形有理三次Ｂ样条插值曲线，最后，给出了两个例子。     

The thermal ignition of lignocellulosics in infinite slab and cubic geometries

Wood shaving samples were heated in both cubic baskets and in a previously described system realising the conditions of the ‘infinite slab’ in thermal ignition. Results from the two sets of experiment were found to be totally consistent with each other.     

Comments on Finley's "Critique of rational-emotive philosophy."

Reply to Finley's (1987; see record 1988-00015-001) critique of rational-emotive philosophy, which claims that Ellis's (1981) response to Sharkey's (1981) criticisms of rational-emotive psychology reveals logical and philosophical confusion. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

数控螺纹车削的单步插补控制法

分析了运动控制芯片MCX34的控制原理及单步插补实现过程，提出了基于运动控制芯片MCX314实现螺纹切削的单步插补控制法，从而实现快速，高效的螺纹加工。该方法控制过程简单 ，同步实现锥螺纹，控制精度高（0.001mm），响应快（≤1.6MHz)，脉冲确保不丢失，解决了数控螺纹车削存在的一系列关键问题。     

Decomposition of Time Series Dynamic Linear Models

This paper derives the admissible decompositions for a time series dynamic linear model, assuming only that the model is observable. The decompositions depend on factorizations of the characteristic polynomial of the state evolution matrix G into relatively prime factors. This generalizes the method of West (1997 ) which considers one decomposition in the particular case where G is diagonalizable. Conditions are derived for a decomposition to be independent. These results show that no autoregressive process of order d has an independent decomposition for any integer d . Two illustrations of this procedure are discussed in detail.     

桥口南--徐集地区三维地震资料连片处理技术

针对东濮桥口南—徐集地区三维地震资料的特点及本区块的地质要求，制定处理流程，应用能量均衡、面元均化、三维道内插、三维DMO叠加及三维一步法偏移等技术方法，研究解决因为不同年代、不同方法、不同参数所采集的地震数据在连片处理时存在的问题，精细处理三维连片资料，满足构造解释精度的要求，对进一步落实该区构造和增储上产具有重要的作用。     

Effect of thermophoresis on particle deposition rate from a natural convection flow onto a vertical wavy plate

This research discusses the impacts of the surface area that the wavy surface gets more than the flat plate upon the aerosol particle deposition. Starting from the full Navier–Stokes equation, the mathematical analysis takes the thermophoretic motion formed by the temperature gradient and the fluid thermal expansion into consideration, and converts the governing equations into the boundary layer equation by the simple coordinate transformation and non-similarity method, and then works out these equations by the Spline Alternating-Direction Implicit method (SADI). The numerical value result reveals that the average deposition effect of the wavy plate is greater than the flat plate and that the increasing rate is nearly equal to the value obtained by dividing the surface area that the wavy plate gets more than the flat plate by 2.2.