无纸化建造

本文通过分析先锋建筑师借鉴汽车制造领域的无纸化技术进行的建造实践,揭示了无纸化建造的操作过程,并探讨了无纸化建造的意义,那就是无纸化不仅改变了传统的设计方法,而且改变了传统的建造方式,这将是人类的建造技术发展史上的一场伟大的变革.文章最后探讨了无纸化建造在中国的实践意义.     

Experimental and numerical investigation of fracture in double-edge notched steel plates

Double-edge notched (DENT) steel plates were pulled until complete fracture and several experimental observations were made (using profilometry and scanning electron microscopy). The essential work of fracture (EWF) model was found to be well verified. Numerical simulations—up to the maximum load only—of some experiments were performed using the finite element method (FEM), and incorporating geometric and material non-linearities (large deformation elasto-plasticity). Some experimental measurements were compared with the corresponding numerical computations and excellent agreement was found.     

Analytical Calculation of Large-Scale Deflection of Pulse-Loaded Elliptic Plates

Large deflections of pulse-loaded elliptic and round plates made of hardenable elastoplastic materials are investigated analytically using an energy-based approach. Formulas that are convenient for engineering design have been derived.     

线加权余量法及其在正交异性板弯曲分析中的应用

利用有限差分法对控制方程和边界条件进行半离散化,使其定义在一些离散线上,然后采用加权余量法求解。这就是本文提出的线加权余量法,也可称之为有限差分-加权余量分维耦合法。文中以正交各向异性薄板弯曲平衡问题为例推导了有关具体算式,给出了数值算例,说明了本文方法的有效性。     

An improved method for magnetic identification and localization of cracks in conductors

A SQUID magnetometer can be used to measure the magnetic field produced by flaws in a two-dimensional, conducting plate carrying a current. Identification of the flaw-induced magnetic field is difficult because of the large magnetic field associated with the edges of the plate and the current in the leads that connect the plate to the power supply. We have developed a technique by which the wire and edge fields can be cancelled prior to mapping the magnetic field. In this technique, a similar unflawed conducting sheet is placed adjacent to the flawed plate, with a connection between the sheet and the plate at one edge, and with the opposite edges of the sheet and of the plate connected to the two conductors of a coaxial cable. Thus, an applied current will flow along one conductor of the cable, across the cancelling sheet, cross into the flawed plate, return along the plate, and then return to the power supply along the other conductor of the coaxial cable. As a result of this geometry, there is no magnetic field from the lead-in wires because they are coaxial, and the magnetic field due to the edges of the plate is cancelled by the opposing magnetic field of the edges in the adjacent sheet. The extent of cancellation is determined primarily by the separation between the plate and the cancelling sheet, by the thickness of the plate, and by macroscopic inhomogeneities in their electrical conductivities.     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

Thermoelastic solutions for orthotropic and anisotropic composite laminates

Solutions, within the framework of linear uncoupled thermoelasticity, are presented for certain problems of flexure of composite laminates. Benchmark numerical results, useful for the validation or otherwise of approximate laminate models, are tabulated. Finally, these results are used to examine the accuracy of the classical lamination theory based on Kirchhoff's hypothesis.     

铁水鱼雷罐的检测方案研究

论文介绍了一种针对铁水鱼雷罐车铁水液位检测的较为可行的低成本方案。采用车上间接称重、远红外非接触传输信号方式，解决了对移动铁水罐车进行实时监测的难题。     

基于面像识别技术的公安网上追逃系统

研究了公安网上追逃系统的体系结构和系统的程序流程，阐述了ASP COM 后台比对服务的3层B／S模式面像网上比对的实现方法，最后给出系统的性能指标和特点。     

孔径法测量铜带残余应力的试验研究

介绍了用于薄板残余应力测量的新方法——孔径法,该方法是通过测量冲孔直径的变化来间接求出各方向的残余应力;文中详细阐述了残余应力的标定方法;由于可针对不同材料建立了被测材料的平均应力(σ_l)与被测板材宽度(B)、厚度(H)以及冲孔后直径变化率(△D_i/D)之间的数学模型,因而使薄板残余应力测量变得简便而经济;此外还对该方法的分辨率与测量精度进行了实验、计算与分析。