联产供冷与电力供冷能耗比较分析

文中将两种供冷能耗比较分解成用电煤耗差、用热煤耗量、增加产汽用电煤耗量三部分进行分析，按照热量法得出在目前一般情况下联产供冷比电力供冷通常费能和定性定量结论，为全面研究比较热电冷联产与分产的能耗奠定一个基础。     

从菜西瓜中提取果胶的最佳工艺研究

为确定从菜西瓜中提取果胶的最佳工艺条件,以山西省临汾市菜西瓜为材料,采用酸法进行了提取果胶的试验研究。正交试验结果表明:在萃取时间为45min的前提下,从瓜瓤中提取果胶的最佳工艺条件是加水量为原料重量的4倍,85℃下,添加原料重量0.3％的多聚磷酸钠,果胶得率可达2.03％;从外果皮中提取果胶,加水量为原料重量的4倍,75℃下,添加原料重量0.7％的多聚磷酸钠,果胶得率可达2.98％。     

Bandpass filters using periodically loaded combline resonators

A novel combline filter is proposed for cellular‐radio base stations. The Q‐factor is significantly improved. The eigenvalue equation is expressed with the single‐team approximation in the gap region of the combline resonator. A two‐pole combline filter is designed. The calculation, simulation, and experiment results are presented and are in good agreement. © 2005 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

AutoCAD 下非结构网格自动生成

在AutoCAD环境下，从背景网格生成和数据结构两方面对推进阵面法进行修正。采用修理后的方法，使得在流场、泥沙输移和床面冲淤数值计算的前处理过程中无须精心预设内部控制点而只需给边界一个尺度，就能自动生成适应任意复杂边界的非结构网格，从而提高网格生成、优化的效率和通用性。     

由乙腈一步法制备乙酸丁酯的研究

以丁醇和制备丙烯腈的副产物乙腈为原料 ,采用一步法合成了乙酸丁酯。通过正交实验得到了影响反应的 4种因素。确定了最佳的工艺条件为 :催化剂的量为样品质量的 40 % ;n(CH3CN)∶ n(C4 H9OH) =1∶ 1 .0 5 ;反应温度为 1 0 5℃ ;反应时间为 8h。在此反应条件下 ,乙酸丁酯的收率为 88.8% ,纯度可达 99.5 %。并用气相色谱及红外光谱对产品的纯度进行了表征     

HP700圆锥破碎机动锥的有限元分析

对HP700圆锥破碎机的主要部件动锥建立了有限元分析模型，用ANSYS软件对动锥进行了有限元强度和刚度分析，结果输出了动锥分布及变形图，对圆锥破碎机的结够设计提供了依据。     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

燃烧—气体容量法测定冶金石灰中的二氧化碳

冶金石灰是石灰石经过工业煅烧的产品。其二氧化碳含量低，且经过高温煅烧后基本不含有机物。无需按照《石灰石、白云石化学分析国家标准中二氧化碳的化学分析方法》中用酸进行试样分解，只需在1200℃高温中灼烧，使石灰中残留的或煅烧后吸收空气中二氧化碳而形成的碳酸盐分解，象通常测定含碳耐火材料中二氧化碳那样，采用气体容量法进行测定。     

A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry