More on Goddard and the Kallikak family photographs.

Discusses retouching of the Kallikak family photographs in H. H. Goddard's (1912) study of mental retardation and heredity, with reference to analyses by R. E. Fancher (see record 1987-31600-001) and S. J. Gould (1981), and concurs with Fancher that the retouching was probably not done for deceitful purposes. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

低负荷维氏硬度法的负荷选择

本文按照维氏硬度测定的技术条件,将基本公式H_v=1854P/D~2加以变换,从而得到一些较为简单的数学关系式.利用这些关系式,可以对不同金属薄带材料,很容易计算出较合理的负荷大小,既能保证不被"打穿",也使视场内有一个适合观测的压痕图象.     

一种制做三维牙——颌骨光弹性模型的新方法

本文提出一种用“整体浇注法”制做三维牙——颌骨光弹性模型的新方法,即用价格便宜的石膏做阴模,先制出与真实牙几何相似的牙光弹性模型和模拟牙周膜的乳胶套,将它们粘接好,然后将其放入颌骨石膏阴模的适当位置,浇入环氧树脂混合液,用“二次固化法”进行固化,即可制成三维牙——颌骨整体光弹性模型。此法能保证模型与实物的严格几何相似和牙周的边界条件相似,使实验精度大大提高且工艺简单、成本低。     

Citations do not solve problems.

D. T. Cambell and D. W. Fiske (1959) made the now-obvious statement that measures of the same variable made by different methods should agree (converge) and certainly should agree better than measures of different variables made by those several methods. Almost everyone accepted that statement, yet the multitrait–multimethod matrices published today show little or no improvement over the published examples cited in 1959. The article raised the conceptual problem of how a variable and its measurement should be linked and the methodological problem of clarifying the nature of methods and their effects. Given these unresolved problems, it is perhaps not surprising that the question of the appropriate statistical analysis of these matrices has also no consensual answer. Perhaps methods and traits or contents are so thoroughly intertwined that their interaction cannot be adequately analyzed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

多媒体课件改变了教师的“主讲”地位

随着高等教育教学改革步伐和数字化教学的不断推进和发展,越来越多的教师热衷于多媒体教学课件的使用和研究,传统的教学模式被逐渐取代,教师教学的主导地位越来越不明显,数字教学的时代悄然而至。     

四辊铝箔轧机预控参数在线整定

介绍Ф210mm/Ф500mm× 800mm四辊液压轧机厚度预控系统中采用人机界面实现参数在线调整的方法,能大大提高预控参数的控制精度,减少轧机产品的厚度误差,是厚度自动控制的一项创新.     

石英砂的相变与换向器套筒铸件的变形

用呋喃树脂石英砂工艺生产牵引电机换向器套筒出现变形、裂纹等铸造缺陷,是由石英砂相变膨胀引起,后用高铬刚玉砂代替石英砂得到解决.     

Effect of deposition conditions on the properties and annealing behavior of cold-sprayed copper

The deposition of copper by cold gas dynamic spraying has attracted much interest in recent years due to the capability to deposit low-porosity oxide-free coatings. However, it is generally found that as-deposited copper has a signicantly greater hardness, and potentially lower ductility, than bulk material. In this article, copper was deposited by cold spraying using helium as the driving gas at both 298 and 523 K. Evidence is presented indicating that the material sprayed at the lower temperature exhibits a lower dislocation density throughout the grain structure than the material sprayed at the higher temperature. The low stacking fault energy of copper restricts recovery during annealing, and thus microstructural changes during annealing only proceed once recrystallization begins. The material sprayed at low temperature (with the low dislocation density) exhibited recrystallization at annealing temperatures as low as 373 K with a corresponding reduction in hardness. However, the copper sprayed with helium at 523 K was resistant to annealing at temperatures up to 473 K where the dislocations in the structure prevented recrystallization. However, at higher temperatures, recrystallization did proceed (with corresponding reductions in hardness). The fracture behavior of the copper that was cold sprayed with helium at 523 K, both in the as-sprayed condition and following annealing, was measured and explained in terms of the annealing mechanisms proposed. The original version of this paper was published in the CD ROM Thermal Spray Connects: Explore Its Surfacing Potential, International Thermal Spray Conference, sponsored by DVS, ASM International, and HW International Institute of Welding, Basel, Switzerland, May 2–4, 2005, DVS-Verlag GmbH, Düsseldorf, Germany.     

涡流检测技术在宝钢热轧轧辊上的应用

介绍了轧辊涡流检测仪的工作要求、设备组成和使用方法,指出对轧辊进行涡流检测可防止爆辊,减少轧辊磨削量。     

冲天炉炉胆的(径向)胀裂问题及其防止措施

冲天炉炉胆径向胀裂问题，也是一道颇有难度的课题，本文提出：用平行四边形、竖立的梯形和微凹矩形三种炉壁断面作为防止措施。