就地补偿在动力厂水泵电机上的应用实例

本文就我公司动力厂给水车间155kW水泵电机，进行无功就地补偿的可行性分析及经济效益研究，对工厂用电如何节能降耗有一定参考价值观。     

冶钢小方坯连铸机结晶器液面控制系统故障分析及对策

本文针对某一钢铁厂的一套小方坯连铸机结晶器液面自动控制系统，对其故障原因进行了深入分析，指出导致系统控制性能达不到设计要求长期无法投入运行的主要原因，并提出了相应的解决方法。     

感应电动机转速对定子电流暂态过程的影响

本文运用根轨迹法，分析了感应电动机转速对定子电流暂态过程的影响。并通过对稳态时定子电流在电压阶跃干扰下的暂太响应分析，验证了结论有效性。     

Activation of action rules in action observation.

Visually perceiving an action may activate corresponding motor programs. This automatic motor activation can occur both for higher level (i.e., the goal of an action) and for lower level (i.e., the specific effector with which it is executed) aspects of an action. The authors used a tool-use action paradigm to experimentally dissociate priming effects for observing the target, the movement, or the target-to-movement mapping of a tool-use action. In 3 experiments, participants took turns in acting, observing the tool-use action of another person in trial n-1, and executing an action in trial n. Trial transitions from n-1 to n were manipulated in 4 conditions with (a) mapping repeated and movement and target changed, (b) target repeated and movement and mapping changed, (c) movement repeated and target and mapping changed, or (d) all components repeated. Results indicate priming effects for repeating the target-to-movement mapping (i.e., the action rule) of a tool-use action and suggest that a rather abstract action schema is activated during action observation. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

丰城电厂1～4号循环水泵电机线圈温度异常分析及处理

分析了循环水泵电机线圈温度高的原因，提出处理温度高的措施并实施。     

第十九讲 电机控制集成电路的选用二相步进电机驱动电路SAA1042的选用

MOTOROLA公司生产的SAA1042芯片用来控制并驱动二相步进电机，文中对其主要特点，引脚功能，技术指标，典型应用等作了介绍。     

汽车组合仪表板控制系统设计

介绍了以PIC16F873单片机为控制核心的汽车组合仪表板控制系统的设计,简述了汽车组合仪表板的基本构成,介绍了汽车组合仪表板控制系统的组成和各部分功能,给出了数据采集处理电路、电源电路等部分硬件电路设计方案,并阐述了一些软件设计算法,如分段插补法和用于平滑指针的软件设计算法等。     

数控加工螺旋凸轮的铣床改造

在普通铣床上实施数控改造后，可应用软件程序使步进电机任意变速，并可在加工过程中任意改变这行方向．从而突破了凸轮加工的传统方式，达到了简化程序、提高效率的同的．     

海洋钻修机采用顶驱装置的可行性研究

在简述海洋钻修机采用顶驱的难点及对顶驱的要求后 ,着重分析了意大利Soilmec公司HTD— 2 0 0液压顶驱的结构、技术指标和参数。针对HZJ30海洋钻修机井架采用前开口、直立无绷绳、双节套装式结构 ,自身不具备较强抗扭能力的特点 ,提出安装顶驱需适当加固井架下体 ,在井架上部采用柔性连接 ,在井架下部采用刚性支架的安装型式。最后对海洋钻修机顶驱的使用环境及预计效果做了初步分析。