Ceramics composites from iron ore tailings and blast furnace slag

The search for materials and methods capable of reducing human impacts on the environment is of utmost importance nowadays. This study's primary purpose was to analyze the technical feasibility of ceramic composites production utilizing Fundão Dam's Iron Ore Tailings (IOT), Blast Furnace Slag (BFS) from charcoal, and Foundry Sand (FS) as partial substitutes for the traditional raw materials – sand and clay – for application in building industry materials. The composites were molded in rectangular specimens and fired at temperatures of 900, 950, 1000, 1050, and 1200 °C. The developed materials were analyzed and characterized by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Thermogravimetry (TGA), and Differential Thermal Analysis (DTA). The obtained materials had flexural strength modulus of up to 12.19 MPa, water absorption ranging from 2 to 22%, linear shrinkage ranging from 0.02 to 6.50%, and apparent density ranging from 2.03 to 1.63 g/cm³. The study of the internal structure formation process revealed the formation of amorphous structures in the composites. The results demonstrated that these waste materials may be jointly used in construction materials, contributing to the reduction of natural resource extraction, besides enabling their correct disposal, minimizing environmental impacts, and improving the life quality of the surrounding communities.     

一种5 重real-time PCR筛查转基因水稻方法的建立

以转基因水稻中最常用的CaMV35S启动子、NOS终止子、Cry1Ab/Ac基因、HPT基因及SPS水稻内标基因为研究对象，利用5 种不同的荧光信号（FAM、HEX、Taxas Red、Cy5、Cy5.5）进行多重实时聚合酶链式反应（real-time polymerase chain reaction，real-time PCR）检测方法的研究。通过引物组合筛选、反应体系优化、特异性测试、灵敏度测试、适用性测试等一系列实验，建立了5 重real-time PCR方法，灵敏度可达0.032%。此方法具有灵敏度高、结果准确、通量大等优点，可实现水稻中转基因成分的快速、高效检测。     

Crystal-field engineering of ultrabroadband mid-infrared emission in Co2+-doped nano-chalcogenide glass composites

Tunable and ultrabroadband mid-infrared (MIR) emissions in the range of 2.5–4.5 μm are firstly reported from Co²⁺-doped nano-chalcogenide (ChG) glass composites. The composites embedded with a variety of binary (ZnS, CdS, ZnSe) and ternary (ZnCdS, ZnSSe) ChG nanocrystals (NCs) can be readily obtained by a simple one-step thermal annealing method. They are highly transparent in the near- and mid-infrared wavelength region. Low-cost and commercially available Er³⁺-doped fiber lasers can be used as the excitation source. By crystal-field engineering of the embedded NCs through cation- or anion-substitution, the emission properties of Co²⁺ including its emission peak wavelength and bandwidth can be tailored in a broad spectral range. The phenomena can be accounted for by crystal-field theory. Such nano-ChG composites, perfectly filling the 3–4 μm spectral gap between the oscillations of Cr²⁺ and Fe²⁺ doped IIVI ChG crystals, may find important MIR photonic applications (e.g., gas sensing), or can be used directly as an efficient pump source for Fe²⁺: IIVI crystals which are suffering from lack of pump sources.     

Three‐dimensional color prediction modeling of single‐ and double‐layered woven fabrics

In this research, the three‐dimensional structural and colorimetric modeling of three‐dimensional woven fabrics was conducted for accurate color predictions. One‐hundred forty single‐ and double‐layered woven samples in a wide range of colors were produced. With the consideration of their three‐dimensional structural parameters, three‐dimensional color prediction models, K/S‐, R‐, and L*a*b*‐based models, were developed through the optimization of previous two‐dimensional models which have been reported to be the three most accurate models for single‐layered woven structures. The accuracy of the new three‐dimensional models was evaluated by calculating the color differences ΔL*, ΔC*, Δh°, and ΔE_CMC(2:1) between the measured and the predicted colors of the samples, and then the error values were compared to those of the two‐dimensional models. As a result, there has been an overall improvement in color predictions of all models with a decrease in ΔE_CMC(2:1) from 10.30 to 5.25 units on average after the three‐dimensional modeling.     

增效过磷酸钙的增效机制及其对玉米生长的影响

利用猪毛、风化煤和腐植酸钠的水解液为增效剂制备了一种增效过磷酸钙,探讨了增效过磷酸钙的增效机制及其对玉米生长的影响。结果表明,蒸馏水浸提条件下,增效过磷酸钙能减缓水溶磷的释放,具备较高的pH值缓冲性。与普通过磷酸钙相比,增效过磷酸钙处理的玉米生物量平均增加了41.9%,吸磷量和吸钙量分别增加了61.7%和27.8%,根系活力增加了24.3%。该研究结果对过磷酸钙生产的技术改进具有指导意义。     

基于热负荷自动调节的延迟焦化加热炉三点注汽量智能优化

针对国内某炼油厂延迟焦化加热炉三点注汽问题，采用热负荷自动调节的算法进行了研究。运用该模型方法，分析了三点注汽量对加热炉热负荷和炉管结焦系数的影响，发现三点注汽量的改变均会对热负荷和炉管结焦系数产生影响，主要表现为提高注汽量将会提高热负荷，同时降低结焦系数；第1点注汽量和第2点注汽量对热负荷和结焦系数的影响较强，第3点注汽量对热负荷和结焦系数的影响较弱。在实际操作中，加热炉中的结焦程度既不能太强也不能太弱，合适的结焦系数能够保证正常开工周期里炉管不结焦，也能保证瓦斯、注汽量等参数的合理分配。通过对热负荷、注汽量的智能分配，可得到不同原料油加工负荷条件下更加合理的装置运行方案。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

碳基采暖电热材料研究进展

近几年,由于节能与环保的需求,电取暖的方式得到大力的推广,电热材料的研究与应用受到人们广泛的重视。非金属碳基电热材料是新型的节能型电热采暖材料,本文重点对影响非金属碳基电热材料中的炭黑基电热材料、碳纤维基电热材料、碳晶电热材料电热性能的因素及相关应用进行了综述。