谈有机膨胀剂的使用

作者认为关于木素磺酸钠的低温起动性能优于腐植酸的看法比较片面,文中详细地分析比较了普遍采用的这两种添加剂的优缺点,并认为腐植酸与木素磺酸钠按一定比例混合使用的方法可以提高电池的充放电性能。     

激光冶炼太阳级硅材料的实验研究

通过实验研究表明，大功率ＣＯ２激光器在廉价硅材料制备中应用的可能性。     

用化学腐蚀制备多孔硅太阳电池减反射膜的研究

采用HF HNO3溶液化学腐蚀 ,在硅片上制备减反射效果优良的多孔硅太阳电池减反射膜 ,借助原子力显微镜 (AFM)和X光电子谱 (XPS)对其表面形貌和成分进行观察 ,发现该膜与电化学阳极腐蚀得到的多孔硅具有相似性 ,其主要成分为非化学配比的硅的氧化物SiOx(X <2 )。采用带积分球的光度分光计 ,测得形成多孔硅减反射膜后 ,硅片表面反射率大大下降 ,,在波长 330～ 80 0nm范围反射率只有 1 5～ 2 9%。研究指出这种强减反射作用 ,与多孔硅具有合适的折射率及其多孔特性的光陷阱作用有关     

Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.     

Influence of the intrinsic layer characteristics on a-Si:H p–i–n solar cell performance analysed by means of a computer simulation

In this paper a set of one-dimensional simulations of a-Si:H p–i–n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift–diffusion and the generation–recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy.     

Critical Speed Control of a Solar Car

The World Solar Challenge is a 3000 km race for solar powered cars across the Australian continent from Darwin to Adelaide. Each car is powered by a panel of photovoltaic cells which convert sunlight into electrical power. The power can be used directly to drive the car or stored in a battery for later use. Previous papers (P. Howlett, P. Pudney, T. Tarnopolskaya, and D. Gates, IMA Journal of Mathematics Applied in Business and Industry vol. 8, pp. 59–81, 1997; P.G. Howlett and P.J. Pudney, Dynamics of Continuous, Discrete and Impulsive Systems vol. 4, pp. 553–567, 1998) using a simplified model of the battery, have shown that the optimal strategy is essentially a speedholding strategy. In this paper, with a more realistic model of the battery, we show that the optimal driving strategy is a critical speed strategy. For an optimal journey with no beginning and no ending the solar car must always travel at the critical speed. For an optimal journey of finite length the speed must be close to the critical speed for most of the journey. The critical speed depends on the solar power and will normally vary slowly with time.     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

A new approach to study organic solar cell using Lambert W-function

Organic photovoltaic solar cells bear an important potential of development in the search for low-cost modules for the production of domestic electricity. One of the main differences between inorganic and organic solar cells is that photo-excitation in these materials does not automatically lead to the generation of free charge carriers, but to bind electron–hole pairs (exciton) with a binding energy of about 0.4 eV. Till now various numerical methods using approximations have been reported to study different aspects of organic solar cells. For the first time an accurate method using Lambert W-function is presented to study different parameters of organic solar cells.     

Sensitizing Mechanism and Adsorption Properties of Dye—Sensitized TiO2 Thin Films

The dye-sensitized TiO2 complex films were prepared by the dye coat onto TiO2 surfaces,and the sensitizing mechanism and adsorption properties of the dye-sensitized TiO2 complex films were inverstigated.The influence of the application conditions of dye adsorbed on TiO2 films on the amount of dye adsorption was discussed.Experimental results show that the concentration,the temperature of dye solutions and the dipping time of TiO2 films in the dye solutions have a significant influence on the amount of dye adsorption.Cell test indicates that the conversion efficiency of light to electricity increases with the amount of dye adsorption.     

Solar assisted cooling with sorption systems: status of the research in Mexico and Latin America

Solar refrigeration projects both national and international with sorption and other refrigeration systems have been developed in Mexico and other Latin American countries in the last 15 years. A review of the main projects, both for solar cooling and refrigeration and the results obtained are presented in this paper. A methodology where 19 solar technologies for cooling were identified is also presented. Although solar cooling is still not an economically viable technology, the advances made and the experience gained in the projects described and the improved systems envisaged, will make solar refrigeration systems play an important role in the future.