Al,Ga取代Bi：DyIG薄膜的磁和磁光特性的研究

本文报道用热分解法在玻璃衬底上制备了Ａｌ和Ｇａ取代的Ｂｉ：ＤＹＩＧ薄膜，对其磁和磁光特性做了详细研究．Ａｌ和Ｇａ取代的薄膜均可获得好的矩形比和高的矫顽力．对于Ｂｉ１．２Ｄｙ１．８Ｆｅ５－ｘＭＸＯ１２（Ｍ＝Ａ１，ＧＺ）薄膜，Ａ１和Ｇ２的最佳替代成份分别为１．０和Ｇ．７；最佳晶化温度分别为７００ｏ℃和６７５℃．在波长５１０ｎｍ附近，法拉第旋转角可达８°／ｕｍ左右．光学吸收和品质因子的研究结果表明，Ａｌ和Ｇａ取代能够影响光学吸收和品质因子，其中Ｇａ取代对光学吸收和品质因子的影响较大．     

反常声电光频谱分析器

介绍了一种新型的反常声电光频谱分析器，它可以采用外加电压的办法改变器件的中心频率，扩大器件的频带宽度，并改善器件在频带宽度范围内的频率响应特性。用ＬｉＮｂＯ３制作了一个６０ＭＨｚ的反常声电光频谱分析器件，测试结果表明，器件中心频率可以由５０ＭＨｚ变到７０ＭＨｚ，频带宽度由原来的２６ＭＨｚ扩大到３７ＭＨｚ。     

Ammonia-water absorption machines for refrigeration: theoretical and real performances

In principle, absorption chillers of the ammonia-water type could work at temperatures well below the usual air-conditioning temperatures, arriving at the range 250–260 K, which can be useful for refrigeration applications. This possibility is studied for an air-cooled machine, comparing the results with the experimental data supplied by a manufacturer that recently commercialized such a refrigerator. The prediction is fair, and the study allows an insight into the internal parameters and into the possible behaviour for more severe conditions than those studied.     

X-ray microtomography: Application to microstructure analysis of a cementitious material during leaching process

Leaching of cementitious materials leads to an increase in porosity, which has important consequences on transport and mechanical properties. The present study outlines the characterization of microstructural evolution in a mortar subjected to a chemical attack, by means of a powerful non-intrusive experimental method, namely synchrotron X-ray computed microtomography. This innovative method is used to measure the variation of porosity in a leached mortar. Having described the effects of leaching in mortar (influences on microstructure and on mechanical properties), we present the accelerated leaching process and the microtomographic analysis that have been used to monitor it. We then investigate the capacity of this method to quantify the evolution of porosity during the leaching process. The method is validated by comparison of the results obtained with data available in the literature.     

Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.     

Visible Light Excitation Characteristics of Novel Infrared Up-conversion Materials

The Fluorescence excitation spectrum, emission spectrum and infrared up-conversion luminescence excitation spectrum are measured. The results of spectrum measurement show that the electron trapping materials CaS: Eu, Sm are of visible light excitation. The mechanism of visible light excitation is analyzed.     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

WCDMA关键技术的研究

本主要讨论WCDMA的关键无线技术，并简要介绍了WCDMA移动通信系统中的智能技术。     

Uncertainty in Quantitative Electron Probe Microanalysis

Quantitative electron probe analysis is based on models based on the physics or x-ray generation, empirically adjusted to the analyses of specimens of known composition. Their accuracy can be estimated by applying them to a set of specimens of presumably well-known composition.