从事放射性个人剂量监测分析与防护调查

为了能及时了解放射性工作人员的受照剂量，以便能够更好地保障放射工作人员的健康与安全，采用热释光测量法对包头地区从事放射性工作的工作人员进行了个人剂量监测，并对他们的剂量当量频数分布进行了统计与分析，对工作环境的防护进行了调查对比，就今后的工作提出建议。     

乳化型轧制液的质量标准研究

对国内目前所使用的冷轧薄钢板(汽车钢板)轧制液母液和乳化液的质量指标及常用试验评定方法进行了考察，并对产品的性能要求进行了研究与分析，制订出一套标准以供参考，包括乳化液稳定性、润滑性、防锈性、抗泡性、使用周期及粘度、闪点等性能。     

激光武器对抗效能指标体系研究

武器系统的效能是规划、研制、配置和部署武器系统的基本依据,是评价武器系统优劣最重要的综合性指标,建立正确的效能指标体系是进行效能分析与评价的前提。在详细研究了激光武器对抗机理、效能指标选用原则的基础上,构建了相对完整的激光武器对抗效能指标体系结构,并提出了在不同作战任务下量度激光武器对抗能力的效能定义。     

加油站油品用体积交接存在的问题及建议

叙述了目前加油站在实行按任意温度下的体积交接，由于未考虑油品体积随温度、压力、密度的变化，出现了零售损耗很大的问题。建议加油站在现阶段采用“准标准体积”交接；在由体积转换为质量计算加油站损溢时，使用油库当月发出的平均密度；当财会核销损溢时，不使用盘存的体积和固定密度进行计算的方法，而使用实际盘点的质量数，以真实反映加油站的当期损溢。     

持续改进求真务实--记宝钢机械厂导入ISO9000质量管理体系标准实绩

简单介绍了宝钢机械厂贯标经验.     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

螺杆泵的检测方法及检测标准制定

螺杆泵检测是避免不合格螺杆泵下井、螺杆泵早期失效和提高螺杆泵使用寿命与采油效益的重要技术手段。重点介绍了模拟不同工况的螺杆泵工作特性检测系统及检测定子通径为10－60mm的定子衬套偏心度检测仪的组成及其检测方法和原理。针对大庆油田的实际情况，在进行大量室内和现场试验的基础上，制定了GLB120－27、GLB40－42和GLB500－14型螺杆泵的检测标准。检测技术及其标准实施以来见到了明显效果。     

悬沙中D〉0．06mm粗粒的粒析级配组成及其改正方法

本文首先简述Ｄ＞０．０６ｍｍ泥沙的粒析沉降特性及其粒径偏粗的原因。继之对悬沙中粒径大于０．０６ｍｍ的粒析级配组成机理，及级配组成不同对标准粒径Ｄｂ与粒析粒径ＤＬ关系的影响进行了详细研究。在以上研究工作的基础上，开展了Ｄｂ与ＤＬ的比较试验，得出了粗、中、细型悬沙的Ｄｂ～ＤＬ关系和对ＤＬ的改正方法。     

制革用水乳型聚氨酯涂饰剂行业标准的制定

本文概述了制定该标准的背景，对标准的主要内容加以科学的阐述。     

On basic definitions of unified fracture mechanics terminology

The adoption of unified fracture mechanics terminology (UFMT) will promote efficient communication between specialists in different fields of fracture research, harmonization of national and international standards relating to fracture mechanics, and last but not least improvement of the existing methodology for teaching and education in fatigue and fracture. In this paper the definitions of some basic and related terms included in different standards on fracture mechanics terminology are confronted with one another. Alternative definitions of the same terms are offered. By this strategy the author tries to show that the definitions of basic and related terms appropriate for the UFMT should emerge as a consequence of harmonizing a crack model with an actual crack and then both taken together with a fracture model, laboratory test methods, and failure assessment codes.Published in Problemy Prochonsti, No. 1, pp. 17–29, January, 1996.This paper is published as a matter of discussion.