Role of Extracellular Vesicles in Epithelial Ovarian Cancer: A Systematic Review

Extracellular vesicles (EVs) are a heterogeneous group of cell-derived submicron vesicles released under physiological or pathological conditions. EVs mediate the cellular crosstalk, thus contributing to defining the tumor microenvironment, including in epithelial ovarian cancer (EOC). The available literature investigating the role of EVs in EOC has been reviewed following PRISMA guidelines, focusing on the role of EVs in early disease diagnosis, metastatic spread, and the development of chemoresistance in EOC. Data were identified from searches of Medline, Current Contents, PubMed, and from references in relevant articles from 2010 to 1 April 2020. The research yielded 194 results. Of these, a total of 36 papers, 9 reviews, and 27 original types of research were retained and analyzed. The literature findings demonstrate that a panel of EV-derived circulating miRNAs may be useful for early diagnosis of EOC. Furthermore, it appears clear that EVs are involved in mediating two crucial processes for metastatic and chemoresistance development: the epithelial–mesenchymal transition, and tumor escape from the immune system response. Further studies, more focused on in vivo evidence, are urgently needed to clarify the role of EV assessment in the clinical management of EOC patients.     

A mixed collector system for phosphate flotation

Flotation has been used in industry for more than a half century as the primary technique for upgrading phosphate. While the flotation of phosphate was inefficient when oleic acid was used alone as a collector, therefore a mixed collector of oleic acid (HOl), linoleic acid (LA) and linolenic acid (LNA) was employed to improve the recovery of phosphate flotation. The batch flotation results showed that the optimal composition of the mixed collector was 54 wt.% HOl, 36 wt.% LA and 10 wt.% LNA. Additionally, the effect of pH on the mixed collector application was studied while considering the surface tension, contact angle and micro-flotation. The results showed that the mixed collector should be used at a pH of 9.5. Above a pH of 9.5, the adsorption of fatty acids dimers on the apatite surface hindered phosphate flotation. The influence of the mixed collector assembly on apatite flotation was also investigated. It was demonstrated that due to its low critical micelle concentration, a sufficiently hydrophobic apatite surface could be generated at a collector concentration of 60 mg/L. In addition, zeta potential experiments suggested that collector adsorption was governed by chemisorption. FTIR and XPS spectra studies further indicated that the chemical reaction involved the carboxyl groups of fatty acids and Ca species at the apatite surface for each fatty acid in the mixed collector.     

Classification and regression models of audio and vibration signals for machine state monitoring in precision machining systems

We present a data-driven method for monitoring machine status in manufacturing processes. Audio and vibration data from precision machining are used for inference in two operating scenarios: (a) variable machine health states (anomaly detection); and (b) settings of machine operation (state estimation). Audio and vibration signals are first processed through Fast Fourier Transform and Principal Component Analysis to extract transformed and informative features. These features are then used in the training of classification and regression models for machine state monitoring. Specifically, three classifiers (K-nearest neighbors, convolutional neural networks and support vector machines) and two regressors (support vector regression and neural network regression) were explored, in terms of their accuracy in machine state prediction. It is shown that the audio and vibration signals are sufficiently rich in information about the machine that 100% state classification accuracy could be accomplished. Data fusion was also explored, showing overall superior accuracy of data-driven regression models.     

Solid state reactions between SiC and Ir

Reactivity between SiC and Ir as a function of SiC-crystallinity was investigated by diffusion bonding technique under a vacuum and over the temperature range of 1200–1450 °C. As reaction products, various Ir-silicides and free unreacted-C were detected. Reactivity is strongly affected by the temperature and SiC-crystallinity involving a series of interactions, from “no reaction” to “massive exothermic reactions”. In particular, interfacial phenomena are more pronounced by the presence of defects and grain boundaries.Solid state reactions result in formation of fine C-precipitates rearranged in a quasi-periodic microstructure. On the contrary, clustering of highly ordered C-precipitates (C-graphitized) occurs after “massive reactions” take place.A relationship between the degree of graphitization (from 1 to multi-layers of graphene), temperature and SiC crystallinity was found by Raman spectroscopy. 2D-layering phenomenon is enhanced in polycrystalline SiC at high temperature.     

Active disturbance rejection based trajectory linearization control for hypersonic reentry vehicle with bounded uncertainties

This paper investigates a novel compound control scheme combined with the advantages of trajectory linearization control (TLC) and alternative active disturbance rejection control (ADRC) for hypersonic reentry vehicle (HRV) attitude tracking system with bounded uncertainties. Firstly, in order to overcome actuator saturation problem, nonlinear tracking differentiator (TD) is applied in the attitude loop to achieve fewer control consumption. Then, linear extended state observers (LESO) are constructed to estimate the uncertainties acting on the LTV system in the attitude and angular rate loop. In addition, feedback linearization (FL) based controllers are designed using estimates of uncertainties generated by LESO in each loop, which enable the tracking error for closed-loop system in the presence of large uncertainties to converge to the residual set of the origin asymptotically. Finally, the compound controllers are derived by integrating with the nominal controller for open-loop nonlinear system and FL based controller. Also, comparisons and simulation results are presented to illustrate the effectiveness of the control strategy.     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.     

Effects of ethylene-octene copolymer (POE) on the brittle to ductile transition of high-density polyethylene/POE blends

Three kinds of ethylene-octene copolymers (POE) were melt-blended with high-density polyethylene (PE-HD) in different proportions. Detailed characterizations were conducted to analyze their structural differences of POE and its effects in toughening PE-HD. The higher molecular weight POE can improve the toughness of PE-HD. 60:40 PE-HD/POE is elongated to break up to 700% while impact strength is 84.7 kJ/m² at −30°C, which is 21-fold of PE-HD. In the brittle to ductile transition (BDT) during impact, the fracture mechanism changes from the crazing mode to the shear yield-plastic deformation mode. The BDT temperature decreases as the POE molecular weight and its content increase. The interface strength in tension is estimated to access their effects. The Boltzmann-type models were successfully extended to describe the typical S-shaped curves in BDT of notched impact strength vs POE content or temperature. The supplementary decay model is suggested for the attenuation in toughening. Transition map in impact is proposed to select the use range of composition (c ) and temperature (T ) for high toughness. The curves are converted into 3D graph of T -c -impact strength for illustrating their coupling-separate effects, and further into the contour map of impact strength in T -c space for finding their partial equivalence.     

Suitability,efficiency and microbiological safety of novel physical technologies for the processing of ready‐to‐eat meals,meats and pumpable products

Consumer studies and market reports show an increase in consumption of ready‐to‐eat (RTE) foods. Although conventional processing technologies can in most cases produce safe products, they can also lead to the degradation of nutritional compounds and negatively affect quality characteristics. Consumers strongly prefer food that is minimally processed with the maximum amount of health‐promoting substances. Novel processing technologies as pre‐ or post‐treatment decontamination methods or as substitutes of conventional technologies have the potential to produce foods that are safe, rich in nutrient content and with superior organoleptic properties. Combining novel with conventional processes can eliminate potential drawbacks of novel technologies. This review examines available scientific information and critically evaluates the suitability and efficiency of various novel thermal and nonthermal technologies in terms of microbial safety, quality as well as nutrient content on the production of RTE meals, meats and pumpable products.     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。