KMLS型立式砂泵的振动噪声产生原因及解决措施

针对KMLS型立式砂泵振动、噪声产生原因及其表现特征,提出了解决措施。通过对这些原因的分析研究,可以提供泵设计者和生产者在减少砂泵振动方面采取相应的措施,使KMLS型立式砂泵能更好的服务于用户。     

高可靠性烧结金属丝网防爆元件的应用研究

烧结金属多孔元件作为隔爆元件的应用，很好地满足了火焰过滤元件的性能要求，进一步拓宽了烧结金属多孔元件的应用领域，章在论述其性能特点、结构类型的同时，对其在微孔结构设计上的差异也进行了描述。     

Termites live in a material world: exploration of their ability to differentiate between food sources.

Drywood termites are able to assess wood size using vibratory signals, although the exact mechanism behind this assessment ability is not known. Important vibratory characteristics such as the modal frequencies of a wooden block depend on its geometry and boundary conditions; however, they are also dependent on the material characteristics of the block, such as mass, density and internal damping. We report here on choice experiments that tested the ability of the drywood termite Cryptotermes secundus to assess wooden block size using a solid wooden block paired with a composite block, the latter made of either wood and aluminium or wood and rubber. Each composite block was constructed to match mass or low-frequency vibratory modes (i.e. fundamental frequency) of the solid wooden block. The termites always chose the blocks with more wood; they moved to the solid wooden blocks usually within a day and then tunnelled further into the solid wooden block by the end of the experiment. Termites offered composite blocks of wood and rubber matched for mass were the slowest to show a preference for the solid wooden block and this preference was the least definitive of any treatment, which indicated that mass and/or damping may play a role in food assessment. This result clearly shows that the termites were not fooled by composite blocks matched for mass or frequency, which implies that they probably employ more than a single simple measure in their food assessment strategy. This implies a degree of sophistication in their ability to assess their environment hitherto unknown. The potential importance of alternative features in the vibrational signals is discussed.     

关于重力坝坝内细部构造设计的几个问题

重力坝常采用横，纵缝将坝体分为柱状体施工。为此，横缝须设置止水，纵缝则待坝体冷却后灌浆，将柱状坝块连成整体。此外坝体内部还须设置坝面排水管以消除坝内渗透压力。关于坝内这些细部构造，设计规范仅有原则性要求，一般专业书列举不多，目前有些工程往往参照已建工程的设计图采用，常由于施工详图不祥易发生施工质量问题。根据丹江口重力坝设计经验，对接缝灌浆中的键槽，止浆片，灌浆管道，出浆盒，排气槽及排气管，基岩陡坡     

往复式压缩机管道的防振设计

分析了往复式压缩机管道产生振动的原因及影响因素,提出解决管道振动的方法及对策。     

高速冷带轧机垂直自激振动稳定性分析的数值计算方法

本文在充分考虑轧机垂直振动过程中辊缝非线性的基础上，利用轧制理论方程和机械振动理论中的能量判据，给出了更精确的分析高速冷轧机垂直自激振动稳定性的数值计算方法。     

非线性隔振理论初探

本文以线必阻尼，立方刚度非线性系统为例，对非线性隔振理论进行了初步探讨，导出了系统的无量纲运动响应和传递率，并与线性隔振系统进行了比较，着重讨论了非线性对它们的影响，获得了一些有用的结论。     

有限周期梁用动力消振器抑振的特性

本文用弯曲波方法导出了多支承梁加动力消振器位移响应的普遍表达式。理论分析发现了周期结构用动力消振器抑制振动的一些新特性：（１）仅用一个动力消振器可抑制周期结构对应传递频带内的一组共振峰。被抑制的共振峰的数量与跨距的数量和消振器的布置位置有关；（２）动力消振器调谐频率与对应传递频带的第一个共振频率相关联。当动力消振器与作用在梁上的外载荷作用在同一点时，最佳调谐频率比总是大于１，否则最佳调谐频率比小于１。     

柔性冗余度机器人残余振动主动控制

研究柔性冗余度机器人的残余振动主动控制问题，设计了具有压电作动器与应变传感器的机敏杆件，建立了受控系统的状态空间表达式，采用独立模态空间控制理论设计LQR状态反馈控制器，并基于对偶原理设计了具有指定收敛特性的Luenberger全维状态观测器，最后，以平面3R柔性冗余度机器人为例进行了计算机仿真，结果表明，采用这种主动控制方法可以显著改善柔性冗余度机器人的动力学品质。     

Response level crossing rate of a linear system excited by a partially specified Gaussian load process

The problem of determining the maximum mean response level crossing rate of a linear system driven by a partially specified Gaussian load process has been considered. The partial specification of the load is given only in terms of its total average energy. The critical input power spectral (PSD) function, which maximizes the mean response level crossing rate, is obtained. The critical input PSD turns out to be highly narrow-banded which fails to capture the erratic nature of the excitation. Consequently, the trade-off curve between the maximum mean response level crossing rate and the maximum disorder in the input process, quantified in terms of its entropy rate, has been generated. The method of Pareto optimization is used to tackle the conflicting objectives of the simultaneous maximization of the mean response level crossing rate and the input entropy rate. The non-linear multi-objective optimization has been carried out using a recently developed multi-criteria genetic algorithm scheme. Illustrative example of determining the critical input of an axially vibrating rod, excited by a partially specified stationary Gaussian load process, has been considered.