一种新的线性分布参数系统辨识方法

本文应用块脉冲函数（ＢＰＦ）将含有未知参数的线性分布参数系统偏微分方程转换为矩阵方程，通过最小二乘法辨识线性分布参数系统的参数，辨识结果表明，ＢＰＦ辨识法具有原理简捷，实现方便，辨识精度高等优点。     

基于信息的智能控制理论研究

本文介绍的基于信息的智能控制理论的发展过程，主要分为智能控制的信息指标和智能控制的信息结构分析两部分，文中在最后对这套理论可能的发展方向进行了探讨。     

可移动机器人的运动学模型与控制原理

本文首先对可移动机器人的运动学进行了分析，建立了运动学模型与控制结构图，然后采用时域分析法对此系统进行了校正，最后通过对此系统的仿真与时测实验，对各校正环节的参数进行了整定。     

大系统分散鲁棒容错控制的进展及主要成果

综述了近２０年来关联大系统分散鲁棒容错控制的研究动态及取得的主要成果。说明了统一地研究分散鲁棒容错控制的必要性。在分散控制、鲁棒控制和容错控制研究领域内，分析了各种设计方法的主导思想及实质；指出了这些研究成果的意义与存在的问题。文中着重论述了分散、鲁棒、容错控制研究方法的发展途径。     

A delta transform approach to loop gain-phase shaping design of robust digital control systems

This paper addresses the existence of loop gain-phase shaping (LGPS) solutions for the design of robust digital control systems for SISO, minimum-phase, continuous-time processes with parametric uncertainty. We develop the frequency response properties of LGPS for discrete-time systems using the Δ-transform, a transform method that applies to both continuous-time and discrete-time systems. A theorem is presented which demonstrates that for reasonable specifications there always exists a sampling period such that the robust digital control problem has a solution. Finally, we offer a procedure for estimating the maximum feasible sampling period for LGPS solutions to robust digital control problems.     

Robust crossfeed design for hovering rotorcraft

Control law design for rotorcraft fly-by-wire systems normally attempts to decouple the angular responses using fixed-gain crossfeeds. This approach can lead to poor decoupling over the frequency range of pilot inputs and increase the load on the feedback loops. In order to improve the decoupling performance, dynamic crossfeeds should be adopted. Moreover, because of the large changes that occur in the aircraft dynamics due to small changes about the nominal design condition, especially for near-hovering flight, the crossfeed design must be ‘robust’. A new low-order matching method is presented here to design robust crossfeed compensators for multi-input, multi-output (MIMO) systems. The technique minimizes cross-coupling given an anticipated set of parameter variations for the range of flight conditions of concern. Results are presented in this paper of an analysis of the pitch/roll coupling of the UH-60 Black Hawk helicopter in near-hovering flight. A robust crossfeed is designed that shows significant improvement in decoupling perfomance and robustness over the fixed-gain or single point dynamic compensators. The design method and results are presented in an easily used graphical format that lends significant physical insight to the design procedure. This plant precompensation technique is an appropriate preliminary step to the design of robust feedback control laws for rotorcraft.     

An explicit finite difference method for finite-time observers

In this paper we present a numerical method for estimating the current state of a nonlinear control system. We use finite differences to discretize a modified version of the finite-time observer equations in James. The discretized equations are simple and easily programmed. The convergence and accuracy of the scheme is proved, and the scheme enjoys a number of important properties: availability of rate of convergence estimates, good robustness characteristics, and the ability to handle certain types of discontinuities in the observations. The major disadvantage is that the number of grid points required increases exponentially with the number of state dimensions.     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

环境保护地理信息系统的设计

本文主要介绍基于计算机网络的通用型环境保护地理信息系统的功能和实现方法。     

Freelance 2000 DCS在轴流机上的应用

简要介绍了Freelance 2000 DCS的功能特点以及轴流机的控制要求.结合轴流机的控制特点，用Freelance 2000 DCS对原模拟电子系统进行改造，实现并改进了轴流机流量－静叶位置调节、防喘振控制、逻辑控制、状态监测、信息管理等功能。改造后的系统可靠性高、技术先进、信息管理功能强，其设计思想和方法均可供石化企业大型压缩机控制系统的设计和改造借鉴。