Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

分子结构对增塑聚氯乙烯性能的影响

研究了聚合度、分子量分布和支化结构对增塑聚氯乙烯加工流变性能和物理力学性能的影响。结果表明，增塑ＰＶＣ的加工流变性能随聚合度的增加而恶化；拓宽分子量分布和引入支化结构均有利于加工流变性能的提高；增塑ＰＶＣ的拉伸强度随聚合度的增加而提高，而压缩永久变形却随之减小；分子量分布对物理力学性能的影响不大；支化ＰＶＣ的拉伸强度略有下降。     

油溶性减阻功能聚合物的研制

介绍了以混合α-烯烃为原料,制备了具有减阻功能的共聚物。讨论了催化剂浓度、聚合温度、预聚合时间、原料单体中杂质含量对共聚物特性粘度和转化率的影响。试验表明,在较低的催化剂浓度和预聚合温度下,能得到较高分子量的聚合物。气相色谱法和DSC法测定其组成和单体混合物的组成基本一致,表明共聚物是一种无规的梳状结构聚合物。该聚合物达到较高特性粘度时,能获得较好的减阻率。     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

超高分子量聚乙烯衬板在煤仓中的应用

介绍了井底煤仓溜煤斜面采用超高分子量聚乙烯衬板安装及应用情况 ,对井底煤仓棚煤原因及解决办法进行了探讨     

热带城市垃圾典型组分的热解特性研究

对热带城市垃圾的几种典型组分进行了热解实验，得到了它们的失重曲线，通过对失重曲线进行分析，得到了这几种典型组分的热解规律，并通过建立热解动力学模型，求出了其中两种组分的活化能E和频率因子A。     

Modeling of the bulk free radical polymerization up to high conversion—three stage polymerization model. II. Number-average molecular weight and apparent initiator efficiency

The equations for predicting the number-average molecular weight are derived on the basis of the three stage polymerization model (TSPM) in this paper. By applying the equations, a plotting approach is proposed to determine the apparent initiator efficiency defined as f[(α_td+1)/2] and the constant of chain transfer to monomer, where f is the initiator efficiency and α_td denotes the fraction of the termination rate constants by disproportionation. Using the approach to plot the experimental data in the literature, it is found that the chain transfer to monomer can be neglected for both methylmethacrylate (MMA) and styrene (St) polymerizations, but it can exert a significant effect on ethylmethacrylate (EMA) polymerization. In addition, the apparent initiator efficiency is found to be independent of reaction temperature and initiator concentration at each stage. The values of f[(α_td+1)/2] at gel effect stage are slightly reduced as compared with that at low conversion stage for MMA and EMA polymerizations. However, it decreases significantly at gel effect stage for St polymerization. Using the equations derived and the apparent initiator efficiencies obtained from TSPM plots, the number-average molecular weights at different conversions can be predicted. Comparisons show that the agreement between predictions and experimental data is satisfactory.     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002     

Thermally induced microstructural changes in cotton fibers: A free‐volume study

I measured positron lifetime in natural polymer–cotton fibers as a function of isochronal annealing temperature in the range 27–290°C. The variations in the positron results indicated structural changes occurring in the cotton fibers and determined the glass‐transition temperature as 80°C. Activation energies were measured separately for the crystalline and amorphous regions, indicating the versatility of the technique. These values were close to the O? H bond dissociation energy, suggesting O? H bond dissociation, the most probable process occurring under thermal treatment. As an extension of the positron results, the molecular weight of the cotton fibers was determined to be 1,200,000 based on free volume, which was within the range suggested for cotton. There seemed to be an indication that crosslinking changed the spiral structure of cotton fibers to the network type. However, this needs to be validated by other measurements. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3336–3345, 2002