CONSTITUTE AND PROPERTY OFα-Ti AFTER HYDRIDING TREATMENT

研究了氢化处理对退火α-Ti 板材的组织、结构及性能的影响。α-Ti 在室温出现两种结构的氢化物:有序的fctγ相(TiH)和fccδ相(TiH_2)。分析了用X 射线衍射只查觉到δ相的原因。氢化物的数量及形态影响除氢后基体的晶粒组织。控制氢含量可以改善拉伸性能及疲劳性能。     

1960年前黄河下游河槽淤积物粒径组成分析

利用1999年汛前深层钻孔取样资料和历年淤积实测大断面资料分析出1960年前无三门峡水库影响的“自然”水沙情况下,下游河道主槽淤积物中d≥0.1 mm以上泥沙占50.7%,比1960-1999年大30个百分点,这种泥沙在下游的淤积比高达83.1%,比0.05 mm以上泥沙的淤积比高39个百分点。指出应在黄河中游寻找出0.1 mm以上的粗泥沙集中来源区作为近期水土保持的重点区域。     

醋酸纤维素—纤维素增强膜的结构特征和分离性能

本文描述了醋酸纤维素－纤维素大孔增强超滤膜的结构特征一分离性能之间的关系。详细论述了膜材料含量和粘连剂含量及其分子量对膜结构和性能的影响。论述了不同配方铸膜液的膜，其孔径，水通量和截留率随操作压力的变化规律。实验证明这种高强度的ＣＡＣ膜经多次重复使用后，其结构性能保持完好。     

Microstructure evolution during metal forming processes

Recrystallization and grain growth evolutions during metal forming processes are considered. Coupling between the thermo-mechanical and microstructure processes is realized. Die forging of a rear-axle flange is simulated numerically on the base of the finite element method. Material parameters of the models are obtained experimentally. The influence of interpass and holding times on grain size distributions in the end product is shown.     

Effect of carbide additions on grain growth in TiC−Ni cermets

The growth of carbide particles in TiC-XC-2 vol.% Ni and TiC-XC-30 vol.% Ni alloys, where X=Zr, Cr, W, Ta and Mo, was fitted to an equation of the form d³-d_o ³=Kt. The grain growth behavior during liquid phase sintering at 1673K decreased markedly with the addition of Mo₂C or WC, changed little for TaC, and increased with the addition of ZrC or Cr₃C₂. The grain contiguity decreased with increasing Ni content in the TiC−Mo₂C−Ni alloy and was greater in the alloys with smaller growth rate constant. Consequently, the effect of carbide addition on the grain growth of 2 vol.% Ni alloys was found to be similar to that of 30 vol.% Ni alloys. The grain growth mechanism could be explained by the effect of contiguous carbide grain boundaries in restricting the overall grain growth, as well as the area of the solid/liquid interfaces in the alloy by the usual solution/reprecipitation model.     

工艺过程中假废品的研究

对机械零件加工过程中出现的假废品现象进行了分析和研究,并提出了判别的方法.     

Role of Specimen Geometry in the Effect of Fiber Orientation on the Thermal Conductivity of a Uniaxial Carbon-Fiber-Reinforced Aluminoborosilicate Glass-Matrix Composite

A study concerning the effect of fiber orientation on the thermal conductivity of a uniaxial carbon-fiber-reinforced borosilicate glass was conducted. For thin specimens, and thick specimens with specimen sides cut parallel to the fiber direction, the dependence of thermal conductivity on fiber orientation showed excellent agreement with theoretical behavior predicted for a composite infinite in extent. In contrast, the thermal conductivity data for rectangular thick specimens fell well below the data for the thin and angled specimens. For fiber orientation of 45° and higher, at which the heat was directed toward the side of the specimen rather than across, the thermal conductivity values showed excellent agreement with theoretical behavior predicted for a finite composite strip with insulated sides.     

现金流量与公司投资决策--从公司规模角度的实证研究

根据现代公司金融理论，将融资因素引进公司的投资模型，研究不同规模的公司投资与现金流量的关系，并探寻不同规模公司投资决策行为差异的背后动机。实证研究发现：大规模公司投资对现金流量的敏感性要高于小规模公司，动因检验的结果表明大规模公司投资依赖于现金流量源于信息不对称理论，小规模公司源于自由现金流量的代理成本理论，这为我国完善资本市场、制定合理政策提供了借鉴的依据。     

土石坝无粘性粗粒料填筑标准和质量评价探讨

土石坝无粘性粗粒料填筑标准往往根据经验确定,而施工质量主要是通过碾压参数控制,理论依据不足。最大干密度和已建工程实践证明表面振动器法最大干密度与实际填筑干密度基本相等,可以直接指导设计和施工,据此提出了设计和施工控制标准;从砂砾石料、堆石料等无粘性粗粒料的特性探讨了填筑标准的适用范围,利用干密度与<5 mm粒径含量关系和填筑干密度,可以准确及时地对照填筑标准作出填筑质量评价结果。