The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

STRUCTURE FORMATION OF COATED FILMS WITH DISPERSED PIGMENTS DURING DRYING

In the drying of coated films with dispersed pigments, such as floppy disks, the structure of the film is formed during the drying process and depends on the drying condition. It is important to understand the structure formation during drying for the design of the dryer and die better quality of the product. We measured die drying characteristics of the film and determined the structure of dried film experimentally. A qualitative model for the structure formation during drying of the coated film is suggested.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Preparation and properties of CuInS2 thin film prepared from electroplated precursor

Thin CuInS₂ films were prepared by sulfurization of Cu/In bi-layers. First, the precursor layer was electroplated onto the treated surface of Mo-coated glass. Observation of the cross-section prepared by focused ion beam (FIB) etching revealed that the void-free film was initially formed on the top surface of the precursor layer and continued to grow until the advancing front of the film reached the Mo layer. The nucleation of voids near the bottom of the CuInS₂ film followed. To determine whether the condition of the Cu/In alloy influences the CuInS₂ quality we investigated the Cu/In alloy state using FIB. We found that the annealed precursor of low Cu/In ratio (1.2) has several voids in the mid position in the layer compared with Cu-rich precursor (1.6). The cross-sectional view of the Cu-rich absorber layer is uniform compared with the low copper absorber layer. Thin film solar cells were fabricated using the CuInS₂ film (Cu/In ratio: 1.2) as an optical absorber layer. It was found that the optimization of a sulfurization period is important in order to improve the cell efficiency. We have not yet obtained good results with high Cu-rich absorber because of a blister problem. This blister was found before sulfurization. So, we are going to solve this blister problem before sulfurization.     

Male pheromone of swift moth,Hepialus hecta L. (Lepidoptera: Hepialidae)

(R)-6-Ethyl-2-methyl-2,3-dihydro-4H-pyran-4-one, (1R,3S,5R)-3-ethyl-1,8-dimethyl-2,9-dioxabicyclo[3.3. 1]non-7-ene, and (1R,3S,5R)-3-ethyl-1,8-dimethyl-2,9-dioxabicyclo[3.3.1]non-7-en-6-one represent the main components in the male pheromone of the swift moth,Hepialus hecta. The amounts of the three components were 40, 5, and 5 g per male, respectively. Structure elucidation of the compounds was based on spectroscopic data as compared to synthetic reference samples. The absolute configurations were determined by gas chromatography on chiral stationary phases; optically active samples served as reference compounds. Electrophysiological and behavioral experiments with natural material and synthetic samples clearly showed the three heterocyclic compounds to act as pheromones. (E, E)--Farnesene represents the main component of the scent secretion of maleHepialus humuli.     

A formation of compatible poly(vinyl alcohol)/alumina gel composite and its properties

A formation of poly(vinyl alcohol) (PVA)/alumina gel composite was investigated with a viewpoint of compatibility of the composite. An alumina sol was prepared from aluminium iso-propoxide (Al(iPro)₃). The alkoxide was hydrolyzed and the resultant hydrate was peptized to a clear sol with acetic acid. The composite were transparent in whole content of alumina. The effects of dispersed alumina on the sorption of water and mechanical properties of composite were examined. The composites containing PVA 40–50% are flexible. They are folded in various forms and can be drawn five times the initial length in humid state. The residues obtained by calcination to remove PVA at 600°C keep its original form and transparency.