Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Evaluation of different coating systems by electrochemical methods

Corrosion protection of organic coated steel is determined by free corrosion potential measurements and impedance spectroscopy. The results are classified by means of very basic considerations and evaluation figures are developed. These electrochemical data are correlated with the extent of the corrosion for each coating system. The evaluation figures are used for ranking coating systems and this ranking is correlated with the ranking with reference to the results of standardized and exposure tests.     

Combinatorial materials research applied to the development of new surface coatings: II. Process capability analysis of the coating formulation workflow

A combinatorial process has been developed for the high throughput production and evaluation of surface coatings. The workflow designed for the production of arrays of liquid coatings involves the robotic transfer of aliquots of solutions of raw materials to an array of glass vials and mixing of the coatings using an unconventional magnetic stirring process. An investigation of the capability of the workflow to accurately and repeatedly prepare coating arrays was conducted as a function of solution viscosity and aliquot size. In addition, mixing capability was evaluated as a function of solution viscosity, total solution volume, and mechanism of stirring. Overall, the results of the study indicated that adequate accuracy and repeatability of the coating preparation process can be achieved as long as raw material solutions are designed such that viscosity is below about 250 cP and aliquot sizes are above about 75 μl. With regard to mixing capability, total solution volume was found to have a profound affect as did the stirring mechanism.     

环保高性能防腐涂料驱动未来市场

介绍了防腐涂料的新品种和防腐体系的选择,指出了我国防腐涂料的发展趋势。     

Direct current bias applied to hot flame diamond deposition produces smooth low friction coatings

As-deposited diamond coatings generally have a high surface roughness which results in a high friction coefficient and extensive wear of the counter material in sliding contact. Therefore several methods for smoothening diamond coatings have been proposed, such as laser polishing, molten metal etching, thermochemical polishing and mechanical polishing. All these methods have some disadvantage e.g. long processing time or high processing temperature. Furthermore, they are all post-deposition treatments i.e. the manufacture of these coatings requires at least two processing steps, deposition and smoothening. With the present method which combines d.c. bias with hot flame diamond deposition, a smooth diamond surface is produced during the actual growth of the film. No post-deposition treatment is necessary. The surface roughness is not dependent on the coating thickness which means that thick coatings with smooth surface can be produced. In fact, the method has a smoothening effect, i.e. rough surfaces can be made smooth. The method is comparable to conventional hot flame deposition of diamond as to growth rate and cost of producing the coatings. The coatings have a nano-crystalline structure and a surface roughness of Ra = 25 nm, and result in a friction coefficient of 0.1 or less in dry sliding and about 0.05 in water-lubricated sliding against cemented carbide. Their wear resistance is virtually the same as that of conventional diamond films.     

紫外光固化聚合物涂层的原位光稳定化研究

选用实验室制备的四种新型反应型受阻胺类光稳定剂(r-HALS):4-甲基丙烯酰氧基-2,2,6,6-四甲基哌啶醇酯(MTMP)、4-丙烯酰氧基-2,2,6,6-四甲基哌啶醇酯(ATMP)、4-甲基丙烯酰氧基-1,2,2,6,6-五甲基哌啶醇酯(MPMP)和4-丙烯酰氧基-1,2,2,6,6-五甲基哌啶醇酯(APMP),实现了紫外光固化聚合物涂层(膜)的原位(in situ)光稳定化。通过室内人工光老化实验和在光氧化过程中黄度指数(Yellowness Index,YI)的监测,再与典型的商用HALS(Tinuvin770和Tinuvin292)进行平行实验对比,考察了r-HALS对紫外光固化聚合物涂层的光防护效果,探索一条紫外光固化聚合物涂层原位(in situ)光稳定化的新途径。     

Ambient flash sintering of reduced graphene oxide/zirconia composites:Role of reduced graphene oxide

Fabrication of graphene/ceramic composites commonly requires a high-temperature sintering step with long times as well as a vacuum or inert atmosphere,which not only results in property degradation but also significant equipment complexity and manufacturing costs.In this work,the ambient flash sintering behavior of reduced graphene oxide/3 mol% yttria-stabilized ZrO₂(rGO/3 YSZ) composites utilizing rGO as both a composite component and a conductive additive is reported.When the sintering condition is carefully optimized,a dense and conductive composite can be achieved at room temperature and in the air within 20 s.The role of the rGO in the FS of the rGO/3 YSZ composites is elucidated,especially with the assistance of a separate investigation on the thermal runaway behavior of the rGO.The work suggests a promising fabrication route for rGO/ceramic composites where the vacuum and furnace are not needed,which is of interest in terms of simplifying the fabrication equipment for energy and cost savings.     

Structure and water-barrier properties of vanadate-based corrosion inhibitor films

Uniform, crack-free vanadium-based corrosion inhibitor films were grown on aluminum alloy 2024. Neutron and X-ray reflectivity were utilized to investigate the structure, water-barrier properties and speciation of the inhibitor film. The top part of the alloy participates in the formation of vanadate film. The similarity of films prepared from H₂O and D₂O implies the vanadate film is not hydrated. The film has a layered structure with vanadium enriched at the alloy interface. The film behaves as an effective water barrier when the thickness is greater than 800 Å. Films grown without K₃Fe[CN]₆ accelerator are found to be extremely thin.     

Effect of organic/inorganic coating on moisture diffusion in a chip-on-board package with globtop

The moisture diffusion in globtop material for a chip-on-board (COB) package coated with SiN_x and silicone, respectively, or coated with SiN_x plus silicone were measured by embedding a humidity sensor in the globtop and recording the capacitive change in three different temperature/humidity environments. The experimental results were simulated by Fick’s diffusion law with finite-element method modeling. The moisture diffusion coefficients and activation energies were calculated to quantitatively compare the moisture-resistance effects of different coatings. For example, at 85°C/85% RH, the moisture diffusion coefficients for the uncoated reference, SiN_x-coated, silicone-coated, and silicone/SiN_x double-layered coated samples are 1E-5, 0.8E-5, 0.7E-5, and 0.2E-5 mm²/s, respectively. The experimental and simulation results show that double-layered coating with silicone/SiN_x has excellent moisture-resistance properties because it not only smoothes the steps on a printed circuit board (PCB) but also keeps the good moisture resistance of the inorganic films.     

A study of the thermal performance of reflective coatings for the urban environment

This paper presents the results of a comparative study aiming to investigate the effect of reflective coatings on lowering surface temperatures of buildings and other surfaces of the urban environment, and thus test their suitability to lower ambient temperatures and fight the heat island effect. In total, 14 types of reflective coatings, selected from the international market were studied, from August to October 2004, on a 24 h basis. These coatings are used in buildings and some of them are used or could be used in the future in other surfaces of the urban environment (sidewalks, parking lots, etc.). In order to investigate the thermal performance of the reflective coatings, surface temperature sensors and a data logging system as well as infrared thermography procedures were used. The spectral reflectance and the infrared emittance of the samples were also measured. The collected data have been extensively analyzed. It was demonstrated that the use of reflective coatings can reduce a white concrete tile’s surface temperature under hot summer conditions by 4 °C and during the night by 2 °C. It can be warmer, than the ambient air by only 2 °C during the day and cooler than the ambient air by 5.9 °C during the night. “Cool” coatings present superior thermal performance even compared to other “cool” materials. This study can assist in choosing more appropriate coatings for building envelopes and other surfaces of the urban environment, and thus contribute to the mitigation of the heat island effect as well as the reduction of cooling loads and electricity consumption of buildings.