Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

化学镀非晶态Ni—B合金的研究

本文通过化学镀方法在铜和钢上沉积非晶态Ni-B合金。着重讨论了还原剂浓度、络合剂浓度对化学镀沉积速率的影响;分析了它的耐蚀原因和其显微硬度随退火温度的变化情况并就其应用和发展略作说明。     

Effect of type of processing on the microstructural features and mechanical properties of Al-Cu/SiC metal matrix composites

In this study, an aluminum based metallic matrix (Al-2wt.% Cu) was reinforced with SiC particulates using a conventional casting technique and a new disintegrated melt deposition technique. Microstructural characterization studies conducted on the samples taken from disintegrated melt deposition technique revealed a more uniform distribution of SiC particulates and good interfacial integrity between SiC particulates and metallic matrix when compared to the conventionally cast composite samples. Results of ambient temperature mechanical tests demonstrate an increase in 0.2% YS and ultimate tensile strength of samples taken from disintegrated melt deposition technique when compared with the unreinforced and conventionally cast composite samples. The results of microstructural characterization and mechanical testing were finally rationalized in terms of the nature of processing technique employed to reinforce Al-2wt.% Cu metallic matrix with SiC particulates.     

New Engineered Particles from Spray Dryers: Research Needs in Spray Drying

This article reviews developments in the simulations of spray dryer behavior, including the challenges in modeling the complex flow patterns inside the equipment, which are often highly transient and three-dimensional in nature. There appears to be considerable scope for using CFD simulations for investigating methods to reduce the rates of wall deposition and of thermal degradation for particles by modifying the air flow patterns in the chamber through small changes in the air inlet geometry. Challenges include building particle drying kinetics and reaction processes, as well as agglomeration behavior, into these simulations. The numerical simulations should be valuable supplements to pilot-scale testing, enabling more extensive and accurate optimization to be carried out than hitherto possible. New understanding of reaction processes and materials science, in combination with recent knowledge of the application of CFD to these problems, may enable new engineered powder products to be developed from the one-step spray-drying process.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

激光法合成SiC超细粉末物理化学过程的研究——Ⅰ.实验规律及粉末特性

用50W连续波CO_2激光器为热源,诱发SiH_4和C_2H_4反应,合成SiC超细粉末。实验确定了反应腔体内压力p、气源中的C/Si原子比、喷嘴内径2r以及激光功率密度与粉末特性之间的关系,并对合成的产物进行物理、化学表征。     

A storage heat pump using an ‘ozone-friendly’ refrigerant

The paper describes the integration of a chemical and a vapour-compression heat pump for energy storage applications. The vapour-compression system is designed to operate using the UK cheap rate ‘Economy 7’ electricity tariff. The system is characterized thermodynamically using various refrigerant/absorbent pairs in the chemical storage circuit and an ozone-friendly refrigerant, R134a, in the vapour-compression circuit. Results indicate that the H₂O/Na₂S pair provides a high energy storage density and is the most suitable for use in this system. The paper also describes the design features of a domestic-sized version of this heat pump system. Air in the sunspace (conservatory) of a house was used as a heat source for the heat pump.     

Silver Electrodeposition from Photographic Processing Solutions

This paper describes the parameters that are important in the industrial practice of silver removal from photographic fixers. The experiments were performed under potentiostatic control using synthetic solutions. The current efficiency was analysed as a function of the cathodic potential taking into account the deposit quality. A cathodic potential of ?0.5 V against a saturated calomel electrode is recommended. The conditions to prevent the darkening of the electrodeposit were investigated. The determination of silver concentration in the solution was made by direct potentiometry. The results obtained with synthetic fixers were corroborated by making the silver deposition from commercial fixers in an electrochemical reactor with rotating cylinder electrode intercalated in an electrolytic flow circuit in order to simulate practical conditions.     

Deposition mechanisms in langmuir-blodgett films

As part of a study of the possible application of polymerisable Langmuir-Blodgett (LB) films as ultra-fine-line e-beam resists, an investigation of the variation of film structure of 22-tricosenoic acid with differing deposition conditions has been made. Unexpected effects with significant implications for deposition speed and resist sensitivity have been observed, and the new techniques for film characterisation developed during the investigation have resulted in a revised model of deposition explaining the observed independence of the disorder causing optical scattering and the macroscopic features observed by polarised microscopy.