Gildes model studies of aqueous chemistry. III. Initial SO2-induced atmospheric corrosion of copper

The GILDES computer model, incorporating Stumm's concept of proton- and ligand-promoted dissolution, has been used to simulate the exposure of copper at room temperature to 210 ppb sulfur dioxide and 80% relative humidity. The agreement is good between the calculations and laboratory exposures performed under these exposure conditions. Surface reactions are relatively more important at lower relative humidities and the dominant corrosion products formed are solid state Cu₂SO₃, CuSO₃ and Cu₂U. Free-radical redox processes are important participants and control the relative distribution of Cu(I)- and Cu(H)-containing corrosion products.     

On the permeation rate of copper extraction through liquid membranes

The understanding of the permeation rate of metal ions through liquid membranes is important for the design of such systems. In this paper, the permeation rates of copper ions through liquid surfactant membranes, including interfacial reaction rates and the diffusion rate of the copper ion, were analyzed using a model based on a mobilized hollow spherical globule configuration. The analysis shows that the extracting reaction is dominant at the external interface of the membrane and the stripping reaction is dominant at the internal interface; this means the reactions at both interfaces are not in equilibrium during the course of extraction. It also shows that the extraction rate, the diffusion rate and the stripping rate are not of equal value, especially at the early stage of the run.     

非金属电镀用导电漆的研制

介绍了导电漆、作为导电填料的片状镀银铜粉的制备工艺流程。分别研究了漆膜表面单位电阻与镀银铜粉的含量及其粒径以及钛酸酯偶联剂的含量之间的关系。结果表明,当镀银铜粉的粒径为400目、质量分数在57%~65%之间,钛酸酯偶联剂的质量分数为10%时,所得涂膜的导电性能最佳。加入含C-18的油酸可以使导电漆长期贮存而电阻值不变。经检测,所得涂膜具有良好的性能:附着力1级,硬度1 H,柔韧性1 mm,冲击强度50 kg/cm2,膜厚10~15μm,漆膜表面每厘米电阻0.15Ω,每分米电阻0.47Ω。指出了导电漆应用过程中的注意事项。     

Reserve estimation of an open pit mine under price uncertainty by real option approach

Reserve estimation is a key to find the correct NPV in a mining project. The most important factor in reserve estimation is the metal price. Metal price fluctuations in recent years were exaggerated, and imposed a high degree of uncertainty to the re-serve estimation, and in consequence to the whole mine planning procedure. Real option approach is an efficient method of deci-sion making in the uncertain conditions. This approach has been used for evaluation of defined natural resources projects until now. This study considering the metal price uncertainty used real option approach to prepare a methodology for reserve estimation in open pit mines. This study was done on a copper cylindrical deposit, but the achieved methodology can be adjusted for all kinds of deposits. This methodology was comprehensively described through the examples in such a manner that can be used by the mine planners.     

铜离子印迹改性壳聚糖海绵的制备及应用研究

以醋酸铜为模板,甲醇、氯仿为溶剂,2-乙烯吡啶、丙烯酰胺为功能单体,乙二醇二甲基丙烯酸酯为交联剂,采用本体聚合法制备铜离子印迹聚合物;然后掺入到壳聚糖海绵的制备中,使壳聚糖海绵对铜离子的吸附率由27．1％提高到72．3％。制备的铜离子印迹改性壳聚糖海绵需要2d达到吸附平衡,吸附-解吸5次后,性能稳定。     

高炉铜冷却壁凝固过程数值模拟

在对铜冷却壁砂型 金属型复合铸造条件下的热态工况进行分析的基础上,利用有限元数值模拟的方法首次建立了铸型传热分析对称模型。在模型中对铸型传热系统中的对流、辐射、接触边界条件和凝固潜热进行了处理,利用有限元分析软件ANSYS,分析了紫铜冷却壁的温度场的变化。数值模拟的结果与实际生产相当吻合。     

Effect of grain size on high-temperature oxidation behavior of Cu-80Ni alloy

1　INTRODUCTIONTheoxidationofunalloyedcopperandnickelhasalreadybeenstudiedindetail.Whilethehigh tem peratureoxidationofCu Nialloys ,alsostudiedanumberoftimestodate[13] ,isanexampleofarela tivelysimpleclassofscalingofbinaryalloysbyasin gleoxidant,becausethemetalsformacontinuousse riesofsolidsolutions ,whiletheiroxides ,CuO ,Cu2 OandNiO ,exhibitsmallmutualsolubilitiesandshowsignificantdifferencesinthethermodynamicstabilityandparabolicgrowthrates .Thus ,copper richalloysformexternalscales…     

Leaded brass rods C 38500 for automatic machining operations: A technical report

C 38500 is a widely used copper alloy with a great variety of applications from decoration and architecture to mechanical/electrical engineering. The chemical composition of this alloy offers superior machinability and subsequently increased productivity in high-speed machining and manufacturing processes. In European countries, this alloy is used primarily as free cutting brass (CW 614N according to EN 12164: 1998), similar to C 36000 alloy, which is used also for thread rolling. The lower percentage of Cu compared to C 36000 (nominal 58% instead of 61%) decreases the cost of the raw materials. This paper reports the principal aspects of microstructure, mechanical properties, and machinability of this alloy in relation to the industrial manufacturing process used.