Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Feasibility analysis of membrane reactors – discovery of reactive arheotropes

A feasibility analysis methodology adopted from reactive distillation is applied to membrane reactors. A model is formulated to depict the reactive liquid phase composition on the retentate side of a continuous type membrane reactor. The effects of both the chemical reaction kinetics and the membrane mass transfer kinetics on the feasible products are elucidated by means of retentate phase diagrams and bifurcation analysis. The proposed method can be applied to various membrane processes, independent of the specific structure of the membrane. Two quaternary reaction systems are considered to illustrate the methodology. In the first hypothetical system, it is shown how selective membranes can influence the sequence of effective volatilities which in turn affects the feasible products of the system. In the second example of practical importance, i.e. the heterogeneously catalysed synthesis of propyl acetate coupled with permeation through a porous polycarbonate membrane, the dusty gas model is applied to describe the component fluxes through the membrane. For the latter reaction system, the existence of reactive arheotrope is demonstrated. Arheotropes represent mass transfer controlled feasible products of membrane separation process.     

ETR Ⅱ-30调速器液压控制系统

ETRⅠ-30调速器是瑞士爱舍维斯工厂生产的具有PID调节规律的电液调速器。本文对其液压控制系统作了较详细的介绍,供有关人员参考。     

Reliability and performance analysis of time – space – time switching networks with multiple separated space switches

Since electronic switching systems usually require very strict reliability requirements as well as good performance objectives, we need to jointly analyse the performance and reliability of switching systems. In this paper, we compare conventional time–space–time switches with single space switches with those with multiple separated space switches, from the viewpoints of reliability and performance. We consider time–space–time switching networks which consist of N incoming time switches, i.e. one NxN space switch, two (N/2)x(N/2) space switches, and four (N/4)x(N/4) space switches. We introduce a Markov reliability model to study the effect of failures and analyse the reliability and performance of three different types of switching networks in terms of average blocking probability and the mean time to unreliable operation, as we vary the offered traffic. As a result, T–S–T switching networks with multiple separated space switches exhibit better performance and reliability than those with single space switches.     

Effect of Bi and Sr concentrations on the formation of the 2223 phase in Bi-Pb-Sb-Sr-Ca-Cu-O materials, obtained under different conditions of thermal treatment

The superconducting properties and the phase and chemical composition of Bi _x Pb_0.3Sb_0.1Sr _y Ca₂Cu₃O_z (x=1.5, 1.6, and 1.7;y=1.9, 2.0, and 2.1) materials synthesized by one-step and multistep thermal treatments have been investigated. The multistep annealing between 825–875°C promotes the 2223 phase. The change of Bi concentration has little effect on the 2223 phase formation, regardless of the kind of thermal treatment used, but increasing the Sr concentration (y> 2) strongly inhibits this phase. It has also been established that the loss of Pb after synthesis depends on the initial Bi concentration. The loss of Pb decreases when the initial Bi content is lower.     

Modified atmosphere packaging of a mixed prepared vegetable salad dish

The aim of this study was to design a modified atmosphere package for a mixed vegetable salad consisting of 75 g of cut carrot, 55 g of cut cucumber, 20 g of sliced garlic and 50 g of whole green pepper. Respiration data of all the components were combined with film permeability data to predict package atmospheres and design optimal packages for experimental testing for improved shelf-life of the produce. The optimal package avoided minimum O₂ and maximum CO₂ tolerance limits, and chilling injury temperatures for any component. A pouch form package made of 27 mm low density polyethylene developed a modified atmosphere of 2.0–2.1% O₂ and 5.5–5.7% CO₂, which was beneficial for all components and provided better quality retention than other test packages.