投资项目经济评价指标的研究

本文在探讨“平坦”模糊数及其运算的基础上,提出模糊内部收益率的概念;并利用Prade与Dubois提出的比较两个模糊数大小的指标,给出“近似相等”的概念;从而给“模糊内部收益率”的计算提供了一个方法。     

基于嵌入式电脑横机控制系统

本文分析了电脑横机的结构与功能,提出了基于嵌入式的电脑横机控制系统,采用了S3C2410为主处理芯片,通过FPGA扩展端口,系统读取织物花型数据,控制横机各个动作子系统来完成编制动作,该电脑横机控制系统与传统电脑横机系统相比较,工作效率高,可移植性强。     

梭形线圈制动绕线架的改进

简要介绍了一种适用于中小型高压电机定子梭形线圈绕制的制动绕线架,它在生产过程中起了减少铜扁线绝缘损伤的作用,并能提高生产效率.     

有机层厚度对OLED性能的影响

采用真空蒸发的方法制备出玻璃衬底ITO／TPD／Alq／A1结构的有机发光器件(OLED)。改变有机层的厚度, 比较不同厚度下OLED的各项性能的差异,包括工作电压,发光效率。实验发现无论增大空穴传输层TPD的厚度 抑或是发光层Alq的厚度都会增大器件的工作电压。发光层Alq厚度的增大还能引起发光效率的增大,而TPD厚 度的增大对发光效率的影响则是复杂的。对于上述现象用隧穿理论以及直带模型进行了解释。对制备高亮度, 高效率低损耗的OLED具有指导意义。     

OLED背光源技术研究进展

有机电致发光二极管(OLED)因其白光材料的多样性、制程的简单性和成本低廉性,特别是其面光源的属性,相较于电致发光二极管(LED)的点光源,更有望成为未来液晶显示器件背光源的主角。介绍了OLED背光源关键技术的最新进展,分别阐述了白光OLED发光效率的提升,OLED器件稳定性和寿命的提高,OLED制备的最新工艺,偏极化的OLED技术,OLED背光源与液晶显示面板匹配技术,还介绍OLED背光源产业发展及发展现状,并对OLED背光源技术的发展趋势进行了展望。     

基于电子商务平台的电子完税系统

本文介绍了在山东省国税系统全面推行的电子完税系统,文章从系统的概要设计、详细设计、数据库设计出发,详细论述了该系统的主要思想和开发过程。最后总结了系统的主要特点。     

基于F型管壳的旋转缝焊技术研究

本文深入研究了旋转缝焊技术,讨论了缝焊中焊边受力、速度变化和热量分布情况,分析了影响旋转缝焊气密性的主要因素.     

Microstructures and degradation of heat sink very-thin quad flat package no-leads Pb-free Sn-Ag-Cu solder joints after thermal aging

Heat sink very-thin quad flat package no-leads (HVQFN) packages soldered with Sn-3.8Ag-0.7Cu on metallized laminate substrates have been put to thermal aging. Temperatures from 140°C to 200°C for times up to 30 weeks were applied. The solder joint microstructure develops intermetallic compound layers and voids within the solder. Due to this, the mechanical reliability of the HVQFN inner lead solder joints is degraded. The intermetallic layers are of the type (Cu, Y)₆Sn₅, with Y=Ni, Au or Ni+Au, as well as Cu₃Sn, and follow a power law with aging time: X=C·tⁿ, where n=0.4 to 1.9 depending on temperature. The voids within the solder are attributed to Sn depletion of the solder in favor of the growth of (Cu,Ni)₆Sn₅. They are more pronounced the less the solder volume is in proportion to the intermetallic diffusion area. The amount of voids is quantified as a percentage of the residual solder. The time to reach the failure criterion of 50%, i.e., t_50%, is related to the absolute temperature according to an Arrhenius equation with an activation energy E_a=0.95 eV. This equation is used for determination of the maximum allowable temperature at a certain required operating lifetime.     

A Typology for Multi-Technology, Multi-Service Broadband Network Synthesis

Current technological possibilities for implementing multi-service networks include both single technology ATM or IP networks and multi-technology networks such as SONET-based or flat networks. However, regardless of the technology employed, the synthesis problem – to optimally route traffic and divide the network's transmission resources between its virtual links – remains of prime importance.In this paper, we review, compare, and classify the extensive recent literature concerning multi-service network synthesis methods. In order to do this, we propose a typology based on switching and control strategies and a general notation that reflects the layered nature of the network. Technology independent mathematical models describe the various, essentially different, approaches presently found in the literature.     

一种小尺寸扁平型光缆护套挤塑工艺的改进

对于小尺寸扁平光缆提出了小型挤塑机加一体式免调模具工艺改进方法,有效解决了传统室外光缆挤塑方法其护套后成品外观结构尺寸及衰减、机械性能不达标问题.