Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.     

Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

Volatile organo-halogen trace analysis in beverages by thin-layer headspace enrichment and electron-capture gas-chromatography

Applicability of thin-layer headspace (TLHS) procedure giving an aqueous concentrate and also classical purge and trap (PT) in off-line mode to isolate and enrich volatile organohalogen compounds in common beverages was tested. Both enrichment tech-niques were used in combination with gas chromatography – electron capture detection (GC-ECD). TLHS, combined with direct aqueous injection (DAI)-GC-ECD, proved applicable in the determination of volatile organohalogen compounds in all studied beverages, while the PT in a version with no preliminary sample pre-treatment was of limited applicability. Detection limits of the TLHS-based procedure were in the order of 1 ppt. Content of volatile organohalogen compounds in a number of beverages available on the Polish market including mineral waters, beers, juices, carbonated and non-carbonated soft drinks, etc. was determined by means of TLHS-DAI-GC-ECD.     

基于正交试验的注塑成型工艺参数CAE模拟设定

运用基于CAE技术的注塑工艺参数优化配置和注塑工艺方案设计的思想,结合正交试验设计方法对工艺参数进行CAE仿真试验,并以零件翘曲变形为优化目标,通过敏感因子分析,获得最佳工艺参数组合.经注塑机试模和三坐标测量机的检测分析,验证了CAE模拟结果的准确性和最佳工艺参数组合在实际生产中的效果.     

电镀塑料制品对结构设计及成形工艺的要求

为保证电镀塑料制品的质量,提出了符合电镀要求的塑料制品设计原则,并且指出在注塑成形时,对塑料经过充分干燥,采用较高的注塑温度,较低的注射压力和较慢的注射速度,是使镀层获得良好结合强度的先决条件。     

上下风向条流动方案分析

本文以上下风向条流动分析为例简要介绍TMPI的作用，通过应用MP16．1软件对两种CAE流动方案进行填充对比分析，得到了一种切实可行的方案，充分展现了CAE技术在浇注系统设计和注射模具开发过程中所起到的突出作用。     

Spin Electronics: From Concentrated to Diluted Magnetic Semiconductors and Beyond

This presentation will review physical properties, relevant to spintronics, of concentrated magnetic semiconductors. Examples from the open literature and current research utilizing thin film EuS will be used as illustrations. New research on potential spin injection materials and spin detection will also be described. This latter work, carried out at MARTECH, the Center for Materials Research and Technology, demonstrates that carriers from the half-metal CrO₂ may be injected across an insulator without loss of (100%) spin polarization. It also features the development of a Hall gradiometer capable of detecting as few as 10⁵ spins.     

2号高炉高冶强下的指标优化措施

在高冶强的生产状态下,高炉如何优化各项技术经济指标,降低其成本,从而提高产品竞争力,是现代高炉操作者积极探索的问题。梅钢2号高炉通过精料、优化操作、改进工艺措施等的实施,实现了高炉高冶强下的指标优化。     

静电感应晶闸管的I-V特性物理分析

考虑到寿命不等时的双注入效应、载流子寿命,特别是少子空穴寿命的变化、电导调制效应、双注入空间电荷限制效应等因素,对静电感应晶闸管(Static Induction Thyristor,简称SITH)在正向阻断态的整个I-V特性进行了分段物理分析,给出了理论解释并进行了计算,得出的结论与实验观测结果相吻合.     

汽车空气流量传感技术现状与发展趋势

电喷系统是汽车的核心控制系统,它以空气流量传感器测量获得的进气量为依据确定喷油量与点火时间,从而使得燃料燃烧在理论空燃比附近,以实现更好的安全性、经济性、动力性以及更低的废气排放。因此,进气量的精确测量对汽车电喷系统具有非常重要的意义。介绍了汽车电喷系统空气流量传感技术的现状、存在的问题及发展趋势,并提出了一种采用平行平板电容原理结合涡街原理的传感方式。