New insights in polarity-dependent oxide breakdown for ultrathin gate oxide

In this work, a quantitative analysis is applied to resolve the newly reported polarity-dependent charge-to-breakdown (Q/sub BD/) data from thick oxides of 6.8 nm down to ultrathin oxides of 1.9 nm. Three independent sets of Q/sub BD/ data, i.e., n/sup +/poly/NFET stressed under inversion and accumulation, and p/sup +/ poly/PFET under accumulation are carefully investigated. The Q/sub BD/ degradation observed for p-type anodes, either poly-Si or Si-substrate, can be nicely understood with the framework of maximum energy released by injected electrons. Thus, this work provides a universal and quantitative account for a variety of experimental observations in the time-to-breakdown (T/sub BD/) and Q/sub BD/ polarity-dependence of oxide breakdown.     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Towards a generalized TLM algorithm for solving arbitraryreciprocal and nonreciprocal planar structures

A generalized transmission line matrix (TLM) algorithm is developed in the frequency domain to tackle arbitrary both reciprocal and nonreciprocal anisotropic waveguiding problems. In particular, the modeling issue for arbitrary planar structures is stressed in this work. A new three-dimensional (3-D) condensed node is used to consider the effect of both electric and magnetic constitutive tensors. Various results indicate how the modal dispersive behavior can be manipulated by changing not only the anisotropic characteristics of the substrate, but also the strip/slot geometry as well as the magnitude and orientation of the applied static magnetic field. The present algorithm is useful for CAD and simulation of a large class of gyrotropic waveguide-based microwave and millimeter-wave circuits     

A microprocessor-based toggle-control lighting system

Analysis, design, practical consideration, and implementation of a microprocessor-based toggle-control lighting system are presented. The system is primarily configured with a power factor corrector (PFC), a square-wave voltage generator, a manually controlled toggle switch, and two relays. Toggling the toggle switch can select a different number of lamps in operation, resulting in a mutual dimming feature. A fluorescent lamp lighting system with this specific ballast gains the merits of lower system cost and more flexibilities in lighting fixture design, as compared to conventional systems     

Transdermal Iontophoretic Delivery of Thyrotropin-Releasing Hormone Across Excised Rabbit Pinna Skin

Enhanced transport of a model peptide drug thyrotropin-releasing hormone (TRH), a tripeptide of molar mass 362 g and a pK_a 6.2, through excised rabbit pinna skin was achieved by means of iontophoresis with continuous current or monophase periodically pulsed current. The resulting flux in the steady state was proportional to the applied current density. In the transdermal iontophoretic delivery of TRH, the pulsed iontophoretic flux exceeded that obtained with a continuous current. At a low ionic strength, an increased degree of protonation in TRH increased the rate of permeation. The flux of TRH in a buffer at pH 4 is greater than that at pH 8 when the ionic strength is 0.1 M. At a greater ionic strength, the trend is reversed. The enhanced flux of unprotonated TRH during transdermal iontophoresis is attributed largely to electro-osmotic volume flow. An increased rate of permeation of TRH crossing the skin is achieved at low ionic strength, moderate pH, and a large duly cycle of current; the frequency of pulsed current had no significant influence on the rate of transdermal iontophoretic delivery of TRH.     

The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

Synthesis, characteristics and oxygen-sensitive properties of SrMgxTi 1 − xO3 nanocrystals

SrMg_xTi_{1 - x}O₃ nanocrystals (x = 0.1–0.6) were synthesized by the stearic acid gel method. Powder samples were characterized by X-ray diffraction and X-ray photoelectron (XP) spectroscopy. The results showed that the lattice parameter a and the O 1s XP spectrum changed not only with the Mg content x but also with the grain size d of the samples. The conductivity of a thick film specimen fabricated on an aluminium oxide wafer was investigated in a nitrogen—oxygen atmosphere.     

MEASUREMENT OF THE SPECIFIC SURFACE AREA OF POWDERS BY THIN LAYER WICKING

The specific surface areas (A) of different clay mineral powders were measured by both the BET method and by thin layer wicking. The values of A for the BET and the wicking experiments coincided within a few percent. Thus, the simple and inexpensive thin layer wicking approach may well suffice to obtain reliable specific surface area values for most powders. From the wicking data it is also possible to obtain a rough estimate of the average particle size.     

Evidence of late palaeozoic thermalwater metallization in South Yongmei Depression

This paper discusses the seafloor thermalwater spout sedimentary activity in South Yongmei Depression according to the following evidences: the Yongmei region was in an extended tectonic environment of metaplateform and locally developed intracontinental rift aulacogen in company with the activity of rich alkali, high potassium volcanics of double-peak type. Several kinds of hydrothermal sedimentary rocks and the ore-bearing sedimentary formations of copper-polymetals, iron and manganese exist in this region with a zoning feature of the seafloor thermalwater spout sedimentation. Project supported by the Science Foundation of NECC for Returns Synopsis of the first author Wu Chengjian, associated professor, born in 1957, majoring in ore deposit and mineralgraphy.