超薄SiO2层的热生长

隧道小孔中超薄ＳｉＯ２的生长是ＥＥＰＲＯＭ电路制造的关键工艺之一。采用ＳＵＰＲＥＭ－Ⅲ工艺模拟程序对超薄ＳｉＯ２的热生长进行了工艺模拟，经过大量的工艺实验及优化，确定了超薄ＳｉＯ２的最佳生长条件，生长出的ＳｉＯ２性能良好，完全可满足ＥＥＰＲＯＭ研制的要求。     

Highly compact AC-AC converter achieving a high voltage transferratio

This paper reports a new, highly integrated modular design approach for pulsewidth-modulation AC-AC converters based on a modular phase-bank structure. Novel high-power 3-in-1 integrated bi-directional power modules (IBPM) rated at 1200-V AC and 150 A and the 3-to-1 phase bank circuits have been successfully developed, fabricated and tested. This enables the modularity design of the multiphase converter systems and reduces the critical parasitic inductance. A theoretical analysis of the IBPM's silicon utilization for this new breed of direct power converters has been outlined. A lab prototype at medium power level has been successfully designed, implemented, and tested with good results. A nearly 460-VRMS out voltage at a 1:0.955 voltage transfer ratio, which, perhaps, is the highest performance reported so far in the literature, has been achieved by the novel two-side modulation control system. The converter-fed AC motor system is able to operate over the 0-240 Hz range with inherent regenerative capability and four-quadrant operation. Potential industrial applications are also briefly highlighted in this paper     

Fine-line conductor manufacturing using drop-on demand PZT printingtechnology

An emerging selective metallization process to fabricate fine-line conductors based on drop-on-demand (DOD) ink jet printing and novel nano-particle fluid suspensions (NPFS) was studied. The suspensions consist of 1-10 nm silver or gold particulates that are homogeneously suspended in an organic carrier. A piezo-electric droplet generator driven by a bipolar voltage signal is used to dispense 50-70 μm diameter droplets traveling at 1-3 m/s before impacting a compliant polyimide substrate. The deposit/substrate composite is subsequently processed at 300°C for 15 min to allow for complete evaporation of the carrier and for sintering of the nano-particles, thereby yielding a finished circuit interconnect. Test vehicles created using this technique exhibit features as fine as 120 μm wide and 1 μm thick with resistivities on the order of 3.5×10^-5 Ωcm. The circuitry performed well under environmental conditioning. As expected, repeatability of circuitry fabrication showed sensitivity to the generation of steady, satellite-free droplets. In an effort to generate droplets consistently, it is essential to develop a strong fundamental understanding of the correlation between device excitation parameters and dispensed fluid properties, and to resolve the microrheological behavior of the NPFS when flowing through the droplet generator     

提高E^2PROM中NMOS管源漏穿通电压的实验研究

为了提高Ｅ＾２ＰＲＯＭ中Ｎ管源漏穿通电压，用实验的方法对制造工艺进行了研究。结果表明，高能量注入是提高ＶＰＴ的有效手段，但受到ｐｎ结击穿的限制，只适用于低区短沟Ｎ管；ＤＤＤ工艺大幅度高ＶＰＴ，但ｐｎ结击穿电压低于２０Ｖ，不能应用于高压ＭＯＳ管；采用适量的防穿通注入和适当增大沟道长度为最理想的工艺途径。     

Stochastic TCP friendliness: Expanding the design space of TCP-friendly traffic control protocols

While the current definition of TCP friendliness has enabled a wide variety of traffic control protocols other than TCP, it still considerably restricts the design space of TCP-friendly traffic control protocols. For example, some multimedia streaming applications prefer a smooth sending rate on a time scale of tens of seconds, however, a UDP flow maintaining such a long smoothness time scale is naturally not TCP friendly by the current definition. In this paper, we propose an innovative method to relatively compare the degrees of TCP friendliness of different traffic control protocols, and use it to define a new class of TCP friendliness definitions, called stochastic TCP friendliness (STF). STF greatly expands the design space of TCP-friendly traffic control protocols, while still effectively maintaining the desired fairness of the Internet. To demonstrate the expanded design space, we also develop a new congestion control protocol, called TCP-friendly CBR-Like Rate Control (TFCBR), for multimedia streaming applications which do not require a high sending rate but prefer a smooth sending rate on a time scale of tens of seconds. TFCBR is stochastically TCP friendly, however, it is not TCP friendly by the current definition.     

Catalytic activities and properties of mesoporous sulfated Al2O3–ZrO2

Mesoporous sulfated Al₂O₃–ZrO₂ (MSAZ) catalysts with large surface areas and pore volumes after calcination at high temperature (650 °C) and with higher Al₂O₃ content than 20wt% were successfully prepared from a template of block copolymer (P84). The MSAZ catalysts were characterized by X-ray diffraction (XRD), N₂ adsorption, transmission electron microscopy (TEM), ²⁷Al magic-angle spinning nuclear magnetic resonance (MAS NMR), thermogravimetric analysis (TG–DTG), temperature-programmed desorption of ammonia (NH₃-TPD) and infrared spectra (IR) of adsorbed pyridine. It is shown that the resulting mesostructured sulfated Al₂O₃–ZrO₂ samples have a well-developed textural mesoporosity. The number of acid sites present on MSAZ catalysts is higher than that on conventional sulfated zirconia, and the former catalysts are more active than the latter one for various acid-catalyzed reactions.     

Composition of mixed octadecadienoates via ozonolysis,chromatography and computer solution of linear equations

An approach to the analysis of 55 possible nonconjugated positional isomers of octadecadienoic acid is described and tested with mixtures of individual synthetic methyl esters. In the first example, by ozonolysis a sevencomponent mixture consisting ofcis,cis 5,12-, 6,10-, 6,11-, 6,12-, 7,12-, 8,12-, and 9,12-octadecadienoates was converted to aldehydes, aldehyde-esters and dialdehydes. These fragments were separated on a 50 m×0.2 mm free fatty acid phase (FFAP) vitreous silica capillary column. Equations for an arbitrarily restricted 12×15 matrix of linear simultaneous equations and a computer solution of the matrix provided the composition of the initial methyl octadecadienoate mixture. The power and significance of this method became apparent with the observation that only two of the seven isomers in the known mixture were resolved as single peaks by state-of-the-art capillary gas chromatography, but all seven were identified and estimated with acceptable error by the ozonolysis-capillary gas chromatography-computer procedure. In a generalized approach to the analysis of the 55 possible nonconjugated isomers, a computer program selects the appropriate matrix of linear simultaneous equations based on the aldehyde data supplied by the analyst. Twenty of 21 combinations of seven isomeric esters taken five at a time have been analyzed to assess the efficiency of the method. To illustrate applicability at this stage of development, the method has been used to analyze the diene products of the hydrazine reduction of γ-linolenic acid and the diene products from the biological desaturation of isomeric monoenes. The possibility of distinguishing geometric and positional isomers of 18∶2 has been opened by the observed separation ofcis-andtrans-unsaturated aldehydes and aldehyde-esters. Presented in part at the 16th World Congress of the International Society for Fat Research, October 4–7, 1983, in Budapest, Hungary, and at the American Oil Chemists' Society Meeting, May 15, 1986, in Honolulu, Hawaii.     

一种新的S/PDIF接收机数据译码的实现方法

论文分析了S/PDIF音频数据流的特点,引入模式识别中的训练机对S/PDIF音频数据流进行现场脉冲宽度特征提取。依据训练机结果建立分类器实现脉冲宽度分类,根据脉冲宽度进行同步前置码和逻辑电平的解码。利用硬件描述语言Verilog进行设计实现与验证,仿真结果说明这种特征提取方法可以提高S/PDIF接收机数据解译码的适应性和准确性。     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

Mathematical model of deoxidization with post stirring in a combined blowing converter

Dissolved oxygen in the steel at the terminal of the converter smelting process is the main cause for the formation of oxide inclusions, and the high terminal oxygen content worsens the steel cleanness. However, post stirring in a combined blowing converter can promote the carbon-oxygen reaction in the liquid steel and reduce the dissolved oxygen content at the terminal of the converter smelting process. Thus, the mathematical model of deoxidization in the post stirring process was obtained, and the rationa...